1978 Ford E-350 Econoline Drivetrains
More 1978 Ford E-350 Econoline Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1978 Ford E-350 Econoline, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1978 Ford E-350 Econoline Drivetrains
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1410 U/Joint Size (Part No.41030)
from
$278.99
Yukon replacement yoke for Dana 60 and 70 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1410 u-joint size
- 4.188″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
USA Standard Gear – Replacement Standard Spider Gear Set For Dana 70, 35 Spline (Part No.39011)
from
$249.99
Product Features:
See More
- Spider gear kit
- Fit Dana Spicer 70 and 80 open differential with 35 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
Yukon Gear – The Carrier Bearing Puller (Part No.56034)
from
$689.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
- Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications
Yukon Gear – Replacement Baffle For Dana 70 & 70HD (Part No.33003)
Yukon Gear – 10.25" Ford Tracloc Pinion Gear Thrust Washer (Part No.33290)
from
$8.99
10.25″ Ford TracLoc pinion gear Thrust washer.
Product Features:
See More
Product Features:
- Pinion gear thrust washer
- Fits Ford 10.25″ with Trac Loc positraction
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.48 INCH / 63 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- NOT PICTURED: TWO DUST SHIELDS
National – Bearings (Part No.HM88542)
from
$22.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Mighty Seal (Part No.30032)
from
$73.99
Yukon Gear & Install Kit package for Standard Rotation Dana 60 & ’89-’98 GM 14T, 4.56. This is a complete package that includes front & rear ring & pinion sets along with the most complete master overhaul kits on the market, giving you everything you need to re-gear the front & rear differential in one easy part number. This package contains a thick rear gear set and a standard thickness front gear set.
Product Features:
See More
Product Features:
- Fits standard rotation Dana Spicer 60 and 1989-1998 GM 10.5″ 14 bolt truck
- 4.56 ratio
- Includes front and rear ring & pinion sets and master overhaul kits
- Thick rear gear set for 4.10 and down carrier
Yukon Gear – Bearing Race Driver (Part No.56014)
from
$215.99
Bearing race driver. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM88510 race
- All steel construction
Yukon Gear – Dana 60/70 Rear Axle Bearing And Seal Kit Replacement (Part No.10055)
from
$136.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Ford E350/F350 F/F Dana 60 & Dana 70 rear replacement axle bearing kit, 67-97. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits 1967-1997 Ford F350 and E350 rear with Dana Spicer 60 or 70
- Includes inner and outer bearings and races and axle seal
- Services one side
Yukon Gear – Dura Grip For Ford 10.25" & 10.5" (Part No.26031)
from
$1195.00
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit fits full floating applications only.
Product Features:
See More
Product Features:
- Fits Ford 10.25″ and 10.5″
- Clutch style positraction
- Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
- Fully rebuildable
- Assembled in the USA
Yukon Gear – Replacement Inner Slinger For Dana 70 (Part No.33013)
National – Bearings (Part No.387A)
from
$22.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Yukon Gear – Super Carrier Shim Kit For Ford 10.25" (Part No.55004)
from
$48.99
10.25″ Ford carrier Supershims.
Product Features:
See More
Product Features:
- Super carrier shim kit for Ford 10.25″ and 10.5″
- Interlocking design makes installation much easier
National – Bearings (Part No.28580)
from
$48.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)
from
$34.99
1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.
Product Features:
See More
Product Features:
- u-joint u-bolt kit
- Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
- 1310 u-joint size
- Includes two u-bolts and four nuts
Yukon Gear – Zip Locker Bulkhead Fitting (Part No.34001)
Yukon Gear – Minor Install Kit For Ford 10.25" Differential (Part No.12032)
from
$186.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (Includes Supershims).
Product Features:
See More
Product Features:
- Fits Ford 10.25″
- Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41026)
from
$179.99
Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1350 u-joint size
- 3.625″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
National – Multi Purpose Bearing (Part No.HB-88508)
from
$55.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)
from
$8.99
Product Features:
See More
- Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
- For Trac Loc positraction applications only
Yukon Gear – Steel Cover For Ford 10.25" (Part No.32324)
USA Standard Gear – Ring/Pinion Sets (Part No.36093)
from
$454.99
Ring/Pinion Sets
Yukon Gear – Carbon Clutch Kit With 14 Plates For 10.25" And 10.5" Ford Posi, Eaton Style (Part No.16099)
from
$404.99
Yukon Carbon Clutch kit with 14 Plates for 10.25″ and 10.5″ Ford posi, Eaton style.
Product Features:
See More
Product Features:
- Clutch kit
- Fits Ford 10.25″ with Eaton positraction
- Carbon fiber clutches
Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)
from
$4.99
Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.
Product Features:
See More
Product Features:
- Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
- 1/2″ x 18 thread
National – Bearings (Part No.HM88510)
from
$14.29
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Dorman – Differential Pinion Yoke Assembly (Part No.697-529)
from
$203.99
Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential end yoke matches the fit and construction of the original yoke
- Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
- Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
- Validated fit – this differential end yoke has been tested to confirm accurate fit
Popular 1978 Ford E-350 Econoline Drivetrains Categories
1978 Ford E-350 Econoline Drivetrains
You count on your 1978 Ford E-350 Econoline to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 274 Drivetrains ranging in price from $3.49 to $1,487.99, you’re sure to find everything you need for your 1978 Ford E-350 Econoline.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 16 different brands like Moog, National, and Driveworks. 1978 Ford E-350 Econoline Drivetrains start as low as $3.49!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 3,771 extensive product reviews on 1978 Ford E-350 Econoline Drivetrains. Some of the top-rated Drivetrains products we carry are Multi Purpose Bearing with 3.4 stars and Multi Purpose Bearing with 4.2 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1978 Ford E-350 Econoline below to get started!
Top-Rated Drivetrains Brands For Your 1978 Ford E-350 Econoline
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1978 Ford E-350 Econoline running right for years to come. In our inventory you’ll find brands like Moog, National, Driveworks, and even more.
Popular Felpro Drivetrains
You’ll find popular Felpro brand products across Differentials. All are waiting to get your 1978 Ford E-350 Econoline back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated MOOG Driveline Products Drivetrains
If MOOG Driveline Products are what you’re looking for, our inventory holds plenty. We stock MOOG Driveline Products brand Drivetrains for your 1978 Ford E-350 Econoline, and some of our most reviewed MOOG Driveline Products parts include:
FAQs for 1978 Ford E-350 Econoline Drivetrains
What are the most purchased Drivetrains for the 1978 Ford E-350 Econoline?
Out of 274 Drivetrains for the 1978 Ford E-350 Econoline, the most popular in our inventory are:
What are the top-rated 1978 Ford E-350 Econoline Drivetrains?
Top-rated Drivetrains for your 1978 Ford E-350 Econoline based on customer reviews/ratings are:
