from

$41.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$284.99

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.

Product Features:

HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$18.09

Bolts on using existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing. Has markings from 16 degrees before top dead center (BTDC) to 4 degrees after top dead center (ATDC).

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing
Timing marks from 16 degrees BTDC to 4 degrees ATDC

from

$1009.99

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
64cc Combustion Chambers Improve Performance
Retain Stock Compression Ratio

from

$116.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$329.99

This fully polished, finned aluminum oil pan is die-cast for a perfect fit. 5 quart capacity. Drain plug & bolts included.

Product Features:

Die Cast Aluminum w/ Finned Bottom
Polished
Includes Drain Plug and Mounting Bolts
5 Quart Capacity

from

$75.99

Chrome plated steel valve covers have a flat smooth top.

Product Features:

Fits 1960-1986 Chevy small block with perimeter bolt valve covers
Tall-style covers provide extra clearance
Chrome plated steel construction
Sold as a pair
Cadmium Plated To Resist Corrosion
Easy Installation

from

$16.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for repair applications
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$376.99

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:

Best with aftermarket torque converters and 9.5:1 compression.
Great high RPM power.
Easy on valve train parts.
Can be used with mild ratio rocker arms and traditional performance valve springs.

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$53.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$16.99

ACCEL Hi-Performance rotors offer superior protection from arc-thru and crossfire. Features hi-performance 60,000 volt alkyd compound, stress-relieved at molding to ensure stability and resist centrifugal forces at high racing RPMs.

Product Features:

Max stability for all RPM ranges
Heavy duty for maximum energy transfer

from

$275.99

Product Features:

GM 10BL 8.2 R/P 3.55

from

$14.99

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

2 in. adjustable range
Includes necessary hardware
Chrome plated
Individually packaged

from

$30.99

Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

Product Features:

PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
Premium quality wire harness and capacitor.

from

$474.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$342.99

Product Features:

Incredible Improvement in Control
Maintains Proper Caster and Camber Alignment
Increase in Handling and Control
Greatly Reduce Wheel Hop on Quick Acceleration
Even Braking Control is Improved
Better Suspension Stability

from

$23.29

Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.

Product Features:

Tear Resistant
Precisely Cut To Match Header

from

$20.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Steel core gasket construction
Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
Not intended for use in emission controlled vehicles.

from

$576.99

Product Features:

6500-10000 RPM Range
Dual Plane Quad Type – 4150 Style Flange
7.13 in. Front Height, 7.13 in. Center Height, 7.13 in. Rear Height
Satin Finish
Base Only

from

$80.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For OEM Hydraulic Roller Lifter Cams Only

from

$59.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$28.99

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Can be trimmed if necessary for modified port applications
Complete with manifold end seals and distributor gasket where applicable
For OE replacement, high performance street, drag race and oval track use

from

$64.99

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome plated Aluminum
O-Ring Style To Prevent Leaks (o-ring included)
Swivels for Hard to Fit Applications
Comes With Allen Head Bolts

from

$47.49

Chevrolet V8 engines with HEI/EST remount mount coil 8132 35362 applications include 1987-93 Cars and 1987-95 Trucks (Supersedes 60110).

Product Features:

Features Protection From Arc Thru And Crossfire
Features 60K V Rated Alkyd Compound

from

$57.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$206.99

Pipe Kit

from

$164.99

New chromed steel pulleys are a replacement for originals and are designed as matched sets to assure correct alignment of the drive belts. They are highly polished then chrome plated. Crankshaft Pulley = 7.30 inch diameter Water Pump Pulley = 6.30 inch diameter

Product Features: