1976 Buick Skylark Performance and Racing Products

Essential Performance and Racing Products for 1976 Buick Skylarks

Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)

Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire

from

$367.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched To Performer Intake PN[5486]
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Accel – Distributor Cap And Rotor Kit (Part No.8130)

Distributor Cap And Rotor Kit

from

$32.88


Product Features:
  • Heavy Duty Cap and Rotor Kit
  • With Brass Inserts
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5794)

Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95

from

$151.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Non-Rotator Style: Dyno Tested and Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

FAG US – CUP (Part No.LM48510)

CUP

from

$7.69
CUP

Mr. Gasket – Water Neck (Part No.2557)

Water Neck

from

$27.49
Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:
  • Complete with o-rings and mounting bolts
  • Features an o-ring style seal to prevent water leaks
  • Chrome plated
  • 1/2″ NPT port can be used for various coolant temp related sensors or switches
See More

Richmond Gear – RngPnn (Part No.69-0169-1)

RngPnn

from

$351.99
RngPnn

MSD Ignition – Rotor; GM HEI (Part No.8410)

Rotor; GM HEI

from

$13.29
Replacement rotor for Chevrolet HEI style distributors.

Product Features:
  • For HEI distributors
  • Resist carbon tracking
  • Low resistance brass
  • Max voltage transfer
  • Molded from insulated material
See More

Weiand – Team G; Intake Manifold (Part No.7531)

Team G; Intake Manifold

from

$999.99


Product Features:
  • Designed For Today’s Larger Cubic Inch Big Block
  • Perfect For Hard Core Drag Racers
  • Permanent Mold Casting Process
  • For Lighter And More Consistent Castings
  • Dyno Proven To Make 17hp More Than Competitors
See More

Edelbrock – Universal Performer EFI Dry Systems for 4, 6 And 8 Cylinder Engine (50-70 Hp) (Part No.71006)

Universal Performer EFI Dry Systems for 4, 6 And 8 Cylinder Engine (50-70 Hp)

from

$926.99


Product Features:
  • Best Way To Get A Major Power Increase
  • Power Increases From 50-70 HP
  • Work With Stock ECU
  • Simple Installation
  • Detailed Instructions
See More

Edelbrock – Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Chevrolet (Part No.7361)

Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Chevrolet

from

$128.99
Product Features:
  • Provides excellent sealing and conformability
  • Releases+N747 clean without sticking, if the engine needs to be disassembled
  • Perfect companion for Edelbrock cylinder heads and intake manifolds
  • Does not include end seals
  • Use of a silicone sealant in place of end seal is recommended
See More

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound (Part No.842453)

50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound

from

$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Lakewood – Drag Shock-70/30:GM (Rear) (Part No.40310)

Drag Shock-70/30:GM (Rear)

from

$104.99
The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:
  • Excellent Weight Transfer
  • Lets Front End Down Quickly
  • Maximum Traction
  • Makes Vehicle Safer
  • Easier Control At End Of Track
  • Better Overall Stability
See More

B & M – Transpak For 68-81 TH 350 Transmission (Part No.30228)

Transpak For 68-81 TH 350 Transmission

from

$141.99
The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:
  • Recalibrate Auto. Transmission
  • Optimum Performance
  • Select Your App. Mode
  • Improves Transmission Life
  • Trans. Removal Not Required
See More

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)

Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set

from

$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Fuel Pump Mounting Plate (Part No.1514)

Fuel Pump Mounting Plate

from

$16.99
Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

Energy Suspension – Tie Rod Dust Boot (Part No.9.13101R)

Tie Rod Dust Boot

from

$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Auto Ventshade (AVS) – Eclipse; Large Hood Scoops (Part No.80001)

Eclipse; Large Hood Scoops

from

$123.99
LUND is the first automotive accessory manufacturer to develop and offer comprehensive packages to customize and personalize trucks, SUVs, and vans. An American-based company and the creator of the wrap hood shield category through the invention of the Interceptor hood shield, LUND designs and manufactures the most stylish, high performance, and premium automotive accessories for trucks and SUVs. Product categories include: Interceptor hood protection, nerf bars, running boards, tonneau covers, exterior accessories, storage boxes, cargo management, and bed accessories.

Product Features:
  • Unique, stylized hood scoops for trucks and cars
  • Transform stock hood into a simulated performance hood
  • Can easily be painted to match any factory color
See More

Mr. Gasket – Oil Pan Bolt Kit (Part No.6088)

Oil Pan Bolt Kit

from

$18.99
Oil Pan Bolt Kit

Motive Gear – Differential Mini Spool (Part No.MS10-28)

Differential Mini Spool

from

$98.99


Product Features:
  • MINI SPOOL GM 10 BOLT 8 1/2″ 28 SPLINE
See More

Mr. Gasket – Differential Cover Kit (Part No.9891)

Differential Cover Kit

from

$65.99
Add some bling to the underside of your car with Mr. Gasket’s chrome differential cover. This chrome-plated steel cover is made to fit GM 10-bolt with 8 1/2 in ring gear. Is a complete kit with a gasket and bolts.

Product Features:
  • Made Of Chrome Plated Steel
  • Fits GM 8.5-Inch 10 Bolt
  • Complete Kit With Gasket And Bolts
See More

Hurst – Manual Shifter, Indy, SSA 3 Speed Shifter (Part No.5010002)

Manual Shifter, Indy, SSA 3 Speed Shifter

from

$369.99
Hurst Indy SSA 3-speed shifter kits are designed to be used on most popular 3-speed transmissions in a wide variety of cars. Applications are determined by transmissions and an exclusive engineered mounting design, for most applications.

Product Features:
  • Spring Loaded Gate
  • Short Precise Throws
  • Chrome Plated Stick
  • All Components Are Plated
  • Complete with Shifter Boot and Hardware
See More

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7828)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$80.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.42-222-4)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$548.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Mallory – Distributor Drive Gear (Part No.29425)

Distributor Drive Gear

from

$117.99
Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:
  • Replacement Distributor Gear
See More

Energy Suspension – Ball Joint Dust Boot Set (Part No.9.13128R)

Ball Joint Dust Boot Set

from

$10.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Lasts Longer
  • Looks Great
See More

Upgrade your 1976 Buick Skylark with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1976 Buick Skylark, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Buick or enhancing its overall performance, Performance and Racing Products are key to keeping your Skylark functioning at its best. At Advance Auto Parts, we offer a wide selection of 99 Performance and Racing Products for the 1976 Buick Skylark, designed to meet your needs without breaking the bank. From Performance Engine replacements to Performance Exhaust Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1976 Buick Skylark at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $1,138.99, with an average price of $300.05. Our 99 Performance and Racing Products in stock come from 19 trusted brands, so you’re sure to find the right part for your 1976 Buick Skylark without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1976 Buick Skylark, we stock popular OEM and aftermarket Performance and Racing Products from top names like MSD Ignition, Mr. Gasket, Energy Suspension, and more. MSD Ignition Performance and Racing Products start at just $13.29 and boast an impressive 4 stars average rating from customers. Mr. Gasket and Energy Suspension also bring quality to the table, with Performance and Racing Products available starting at $9.99, and at an average 4 stars rating. With 1,352 customer reviews and counting, our 1976 Buick Skylark Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1976 Buick Skylark is always ready to roll. We’re committed to providing you with everything you need to keep your Skylark in top shape, all in one place. Start shopping confidently below for your 1976 Buick Skylark!

Best-Selling Performance Engines for 1976 Buick Skylarks

Enhance the driving experience in your Buick with 19 quality Performance Engine components, starting at $18.29.

B & M – Tork Master 3000 (Part No.20402)

Tork Master 3000

from

$499.99
Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
  • Washer Between Turbine and Cover
See More

B & M – Tork Master 2400 (Part No.20404)

Tork Master 2400

from

$339.99
Torque Converter – Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best value priced street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New alloy steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required. Due to torque converter core availability, the actual converter size may vary but performance functionality will be as advertised.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1800)

PERFORMANCE OIL PAN GASKET SET

from

$18.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Water Neck (Part No.2557)

Water Neck

from

$27.49
Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:
  • Complete with o-rings and mounting bolts
  • Features an o-ring style seal to prevent water leaks
  • Chrome plated
  • 1/2″ NPT port can be used for various coolant temp related sensors or switches
See More

B & M – Performance Torque Converter for GM TH400, 350, & 375 Transmissions (Part No.20400)

Performance Torque Converter for GM TH400, 350, & 375 Transmissions

from

$299.99
Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)

Ultra Seal: Head Gasket

from

$68.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.130 inch, Compressed thickness 0.055 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Edelbrock – Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire (Part No.5487)

Performer-Plus Camshaft Kit for Buick 231-252 V6 Even Fire

from

$367.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched To Performer Intake PN[5486]
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$94.99
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1000)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$59.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Performer Buick 3.8L, 4.1L V6 Intake Manifold (Part No.5486)

Performer Buick 3.8L, 4.1L V6 Intake Manifold

from

$381.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • Not for C-3 and C-4 Electronic Fuel Mngmt Systems
See More

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)

Torque Converter, Nitrous Holeshot 3600

from

$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:
  • 3400-3800 RPM
  • Small And Big Blocks
  • Serious Performance
  • Furnace Brazed
  • Fully Balanced
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.42-222-4)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$548.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

B & M – Holeshot 2400 (Part No.20412)

Holeshot 2400

from

$499.99
HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

Competition Cams – Xtreme Energy 224/230 Hydraulic Flat Cam (Part No.42-223-4)

Xtreme Energy 224/230 Hydraulic Flat Cam

from

$337.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – Thumpr 226/241 Hydraulic Flat Cam (Part No.42-600-5)

Thumpr 226/241 Hydraulic Flat Cam

from

$324.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:
  • Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
  • Best with aftermarket converters and more rear gear.
  • Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7828)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$80.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
See More

Most Popular 1976 Buick Skylark Performance Exhaust Products

Customize your Buick with 4 Performance Exhaust Products products like Performance Exhaust Mufflers, all priced under $175.99.

Flowmaster Inc. – Super 44 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942448)

Super 44 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound

from

$113.99
Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.42443)

40 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound

from

$99.99
The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound (Part No.942453)

50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound

from

$139.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Flowmaster Inc. – 50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound (Part No.842453)

50 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Moderate Sound

from

$175.99
The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.
See More

Top Picks for 1976 Buick Skylark Performance Distributors

Upgrade Buick Skylarks with top-quality Performance Distributors parts, including 5 OEM and aftermarket selections for your 1976 model.

PerTronix – D9001 Flame-Thrower HEI Distributor Advance Curve Kit (Part No.D9001)

D9001 Flame-Thrower HEI Distributor Advance Curve Kit

from

$26.99
Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

Product Features:
  • PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
  • Precision machined chromoly weights and center plate.
See More

MSD Ignition – Distributor Cap; GM HEI; Red (Part No.8411)

Distributor Cap; GM HEI; Red

from

$49.49
The cap of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap. To make things easy, we now offer these caps as replacement kits.

Product Features:
  • Stock GM HEI replacement distributor cap
  • Red
See More

MSD Ignition – Distributor Cap and Rotor; GM HEI Distributor; Red (Part No.8416)

Distributor Cap and Rotor; GM HEI Distributor; Red

from

$46.49
The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:
  • Designed w/Performance In Mind
  • High Quality Material
  • Stainless Terminals
  • Performance replacement part
See More

PerTronix – D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor (Part No.D9007)

D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor

from

$30.99
Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

Product Features:
  • PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
  • Premium quality wire harness and capacitor.
See More

MSD Ignition – Rotor; GM HEI (Part No.8410)

Rotor; GM HEI

from

$13.29
Replacement rotor for Chevrolet HEI style distributors.

Product Features:
  • For HEI distributors
  • Resist carbon tracking
  • Low resistance brass
  • Max voltage transfer
  • Molded from insulated material
See More

In-Demand Performance Ignition Products for 1976 Buick Skylarks

Select from 8 premium Performance Ignition Products parts for your 1976 Buick Skylark, with prices ranging from $30.49 to $186.99.

MSD Ignition – High Energy Ignition Coil for GM HEI Distributors (Part No.8225)

High Energy Ignition Coil for GM HEI Distributors

from

$112.99
HEI owners now have a choice to replace their stock coil with the MSD high energy unitized coil for GM HEI distributors. This coil is a direct replacement of the stock coil and offers increased spark energy when used with the MSD HEI module, PN 83645. The coil features special low induc?tance, high temperature windings which charge faster to give you increased spark energy at higher rpm. The premium epoxy filled construction is designed to withstand harsh race applications as well as the wear and tear that daily usage dishes out, and still deliver more spark energy to the spark plugs.

Product Features:
  • Direct performance replacement for GM HEI coil-in-cap dist.
  • 70:1 Turns Ratio
  • Lower Primary Resistance Produces High Voltage Output
  • Full Power Sparks To 9000 Rpm w/PN[83647] MSD HEI Module
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Accel – GM Hei Supercoil Red/White (Part No.140005)

GM Hei Supercoil Red/White

from

$113.99
Engineered for higher energy output resulting in quicker starting, improved idle quality, crisper throttle response and more high RPM power. Compatible with both original HEI ignition systems and later model computer controlled HEI systems. No need to remove or re-time distributor. Complete with simplified ground strap, mounting screws, silicone coil gasket and carbon contact brush / spring.

Product Features:
  • 10-15% More Energy
  • Direct Plug In Replacement Direct OE Fit
  • Advanced Bobbin Technology
  • Highly Specialized Silicone Magnetic Steel Cores
  • Similar to Standard Motor Products SMP Dr-32
  • Long Life And Great Looks
See More

Accel – High Performance Ignition Module for GM HEI Distributors (Part No.35361)

High Performance Ignition Module for GM HEI Distributors

from

$69.99
This high performance HEI module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most GM HEI for V8 engines with the 4 pin module 1974 thru 1985

Product Features:
  • Fits Most Stock And Modified Distributors
  • Solid State Electronics
  • Dwell Control Circuit
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

MSD Ignition – Mod HEI Dust Cover, V8 & Odd Fire V6 (Part No.8401)

Mod HEI Dust Cover, V8 & Odd Fire V6

from

$72.99
Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:
  • Externally mounted coil
  • Increases reliability
  • Increase performance
  • High quality plastic
  • Resist spark loss
  • Use brass conductors
  • Low resistance connections
  • No modifications
See More

Mr. Gasket – HEI Adjustable Vacuum Advance Kit – Includes weights, camplate, and bushings – Improve performance (Part No.6011)

HEI Adjustable Vacuum Advance Kit - Includes weights, camplate, and bushings - Improve performance

from

$55.99
HEI Adjustable Vacuum Advance Kit – Includes weights, camplate, and bushings – Improve performance

Most Sold 1976 Buick Skylark Performance Fuel Systems

Explore our best-selling Buick parts for the 1976 Skylark among 5 OEM and aftermarket options starting from $12.99.

Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)

Fuel Pump Block-Off Plate

from

$12.99
This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.

Product Features:
  • Chrome Plated Steel
  • Comes With Gasket
See More

Edelbrock – Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1411)

Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$494.99
The Edelbrock 1411 Performer Series 750 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)

Sbc Blk Off Plate W/Bolts

from

$12.99
Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.

Product Features:
  • Necessary if switching to electric fuel pump
  • Includes block off plate gasket
  • Includes chrome mounting bolts with washers
  • Triple chrome plated
See More

Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)

Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$498.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Electric Choke Installed from Factory
  • Smooth Secondary Transition
  • Includes Only Timed Vacuum Port
  • Includes EGR ; Fuel Vapor Outlet
See More

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)

Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$538.99
The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
  • Can Easily Calibrate with Rods and Jets
See More

Top-Rated Performance and Racing Products Brands For Your 1976 Buick Skylark

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1976 Buick Skylarks. Below you’ll find some of our best rated Performance and Racing Products from MSD Ignition, Mr. Gasket, and Energy Suspension, and more. Performance and Racing Products from these brands that fit a 1976 Skylark start at just $9.99 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular MSD Ignition 1976 Buick Skylark Performance and Racing Products

When it comes to maintaining or upgrading your 1976 Buick Skylark, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. MSD Ignition ticks all of those boxes. We offer a wide selection of MSD Ignition Performance and Racing Products, specifically designed for the 1976 Buick Skylark. With over 5 MSD Ignition brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $13.29, with an average price of just $59.05. Plus, with over 51 customer reviews and an average rating of 4 stars, you can trust that our MSD Ignition Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Rotor; GM HEI
from
$13.29
This product is not rated

Rotor; GM HEI

“”

Mod HEI Dust Cover, V8 & Odd Fire V6
from
$72.99
This product is not rated

Mod HEI Dust Cover, V8 & Odd Fire V6

“”

High Energy Ignition Coil for GM HEI Distributors
from
$112.99

(1)

High Energy Ignition Coil for GM HEI Distributors

“MSD ‘gets it’.”

Popular Mr. Gasket 1976 Buick Skylark Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1976 Buick Skylark owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1976 Skylark, Advance Auto Parts carries a full inventory of 9 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Buick in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $12.99 to $94.99, plus, with more than 28 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

Water Neck
from
$27.49
This product is not rated

Water Neck

“”

Ultra Seal: Head Gasket
from
$68.99
This product is not rated

Ultra Seal: Head Gasket

“”

Thermocap Radiator Cap
from
$48.09
This product is not rated

Thermocap Radiator Cap

“”

FAQs for 1976 Buick Skylark Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1976 Buick Skylarks?

Out of 99 Performance and Racing Products that fit 1976 Buick Skylarks, the following parts are the top sellers:

What’s the price range for 1976 Buick Skylark Performance and Racing Products?

Performance and Racing Product prices for the 1976 Buick Skylark start at $7.69 and go up to $1,138.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1976 Buick Skylark?

The average price for Performance and Racing Products for the 1976 Buick Skylark is $300.05. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Buick Skylark model years?

Yes, we currently carry Performance and Racing Products for 36 model years of Buick Skylarks between 1954 and 1998. Performance and Racing Products are bought most frequently for the following model years: 1998, 1997, 1996, 1995, 1994, 1993, 1992, 1991, and 1990.

What are the cheapest Performance and Racing Products for my 1976 Buick Skylark?

The cheapest 1976 Buick Skylark Performance and Racing Products we carry in stock are:

What are the top-rated Performance and Racing Products that fit the 1976 Buick Skylark?

Out of 1,352 reviews by customers, our 1976 Buick Skylark Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1976 Buick Skylark and their top-rated products:

Can I get help with 1976 Buick Skylark Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Buick Performance and Racing Products and more.

What is your return policy for Buick Skylark Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Buick Skylark Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.