1974 Oldsmobile Delta 88 Performance Engines

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 2800-3200 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

Product Features:

• Timing Chain Only

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• 50 State Street Legal
• Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. brbrFits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:

• Provides Excellent Flange Sealing And Durability
• For High-Performance Street, Drag Race & Oval Track Use

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are an extra thick .312 inch which can help with valvetrain clearance.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
• Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
• For OE replacement, high performance street, drag race and oval track
• An extra thick .312″ which can help with valvetrain clearance

Mr. Gasket Performance Series intake gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Performance Material – Cellulose/Nitrile Composition Gasket Material
• Intake Gaskets are .060″ Thick
• Can Be Trimmed if Necessary for Modified Port Applications
• Comes with Manifold End Seals and Distributor Gasket
• OE replacement for high performance street, drag race, and oval track usage.
• Cork End Seal Gaskets

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Kits include all gaskets needed for a complete engine overhaul. Cylinder head, intake, exhaust, valve cover and oil pan. Distributor gasket (where applicable), timing cover, fuel pump, thermostat, water pump, and rear main seal. For OE replacement, high performance street, drag race and oval track.

Product Features:

• Engine Rebuilder
• Stock/Non-High Performance Engines
• Includes All Gaskets/Seals

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Product Features:

• Use W/ Valve Springs Part #5703, 5794
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Product Features:

• Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

• Fits Chevy engines
• Includes a 1/2 inch NPT threaded hole for by-pass hose
• Includes bolts
• Chrome plated
• Easy to install
• O-ring/gasket not included

Product Features:

• Remote Thermostat Housing

Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:

• Fits Oldsmobile 330, 350, 425 and 455 engines
• Chrome plated
• Bolts included
• Designed for OEM fit
• Easy to install
• O-ring/gasket not included

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Mr. Gasket Copper Head Gaskets are manufactured from dead soft solid copper that provides excellent stability and reduces cylinder bore distortion. They can be used with or without stainless steel o-rings. For supercharged, turbocharged, nitrous oxide and extreme compression ratios. For high performance street, drag race and oval track applications.

Product Features:

• Manufactured from dead soft copper
• .020″ thick
• Provides excellent sealing and durability
• Conforms to and seals minor surface irregularities
• For high performance street, drag race, oval track and turbocharged (extreme heat) applications

Product Features:

• 4.125 in. Cylinder Bore Diameter
• 0.039 in. Thickness
• 8.7cc Volume
• Charcoal Color
• Two Piece Configuration

New Everbright(TM) Manifold coating now available on the most popular Weiand and Holley intakes uses proprietary vacuum metalizing technology combined with a protective clear powdercoat to provide long lasting, virtually maintenance free polished looks.

Product Features:

• Low Rise/Dual Plane Design For Maximum Torque
• Permanent Mold Casting Process
• Lighter/Smoother/Better Looking/Consistent Casting
• Dyno Proven To Make 25hp Over Competition
• Fully CNC Machined For A Perfect Fit
• Square Bore Carburetor Flange
• Exhaust Crossover For Improved Street Drivability

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 Deg Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Accepts Late-Model Choke; Waterneck; and HEI
• Accepts A/C And Alternator
• Accepts Exhaust Heated Chokes

Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:

• Chrome plated
• Grade 8
• 12-point head
• AN washers with no exposed shoulder for a professional appearance