1974 Ford F-350 Pickup Differentials

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Product Features:

• DANA-80 R/P 4.63 STD MG

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Product Features:

• Fits 1988-1998 F350
• 4340 Chromoly
• Left hand inner axle
• 35 spline
• 36.97″ from end of splines to center of u-joint bore

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Yukon forged replacement yoke for Dana 60, stronger than billet, with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60, 70, 70U and 70HD
• 29 spline
• 1350 u-joint size
• 3.625″ snap ring span
• 1.188″ cap diameter
• Outside snap ring design
• U-bolt style

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 70U
• Included are a pinion seal, complete shim kit, marking compound and brush.

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-60 TIMKEN MASTER KIT

Product Features:

• Cross pin shaft
• Fits Dana Spicer 50

Product Features:

• Carrier shims for Dana Spicer 60 and 70U

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Repleacement ring gear bolt for Dana 80. 9/16″ x 18.

Product Features:

• Ring gear bolt for Dana Spicer 80
• 9/16″ x 18 thread

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

Product Features:

• KIT SHIM PINION

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 60 rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

aFe Powers new rear differential cover brings performance engineering to the protection of your axles differential. This differential cover is constructed out of durable die cast aluminum with reinforced ribs and wrinkle black powder coating for maximum strength and styling. This cover comes with all necessary hardware and includes an O-ring for a leak free seal. This cover has about a 5 quart lube capacity at the factory line; factory cover holds about 4 quarts. Built-in internal and external fins transfer heat from the fluid to the outside air for maximum cooling. This system incorporates a large magnetic drain and fill plug that captures loose particles for maximum rear-end protection. Pre-installed large oil level sight glass with calibration plug set to the factory fluid level to eliminate overfilling.

Product Features:

• 5 Quart Lube Capacity
• Built In Internal/External Fins
• Magnetic Drain Plug
• Optional Accessories Available

Product Features:

• Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Product Features:

• Pinion nut washer
• Fits Dana Spicer 80

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

10.25″ & 10.5″ cover gasket.

Product Features:

• Cover gasket
• Fits Ford 10.25″ and 10.5″

Product Features:

• Oil baffle
• Fits Dana Spicer 70 and 70HD

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Fits standard rotation Dana Spicer 60
• 9.75″ ring gear diameter
• 29 spline pinion
• 12 ring gear bolts
• 4.56 ratio

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Bearing race driver for Dana 44 front (TK 02820). No return.

Product Features:

• Bearing race driver
• Fits 02820 race
• All steel construction

55P Chevy Passenger Drop Out gasket.

Product Features:

• Side gear thrust washer
• Fits Ford 10.25″