from

$30.99

Product Features:

Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$8.99

Product Features:

Trac Loc spring for Ford 8″ and 9″

from

$156.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$331.99

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$288.99

Product Features:

Nodular iron for added strength
Thick design
Durable powder coat finish
Magnetic drain plug
Made in USA
High strength stainless steel fasteners

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$12.99

Product Features:

KIT SHIM

from

$579.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit uses the factory side gears.

Product Features:

Fits Ford 8″ and 9″ with 28 or 31 spline axles
Made from 9310 steel for added strength
Works with stock side gears in standard carrier case

from

$225.99

Product Features:

Fits Dana Spicer 60 rear
Uses Koyo bearings and races
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$179.99

Product Features:

FRD 10BL 8.8 R/P 3.55A MG

from

$6.99

Product Features:

Oil baffle for Dana Spicer 60 and Dana Spicer 70U

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$19.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$869.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.73 ratio and down only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$16.49

Product Features:

Brand may vary by location

from

$27.99

Product Features:

Bulkhead fitting

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 44

from

$533.99

Product Features:

NODULAR HOUSING 9″ FORD 3.25″ BORE

from

$7.29

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$7.99

Replacement pinion nut for Dana 44 JK, 44HD, 60, 70, 70U, 70HD & Nissan Titan rear. 1 5/16″ nut, 7/8″ x 14 thread.

Product Features:

Pinion nut for Jeep JK rear, Dana Spicer 44HD, 60, 70, 70U, 70HD and Nissan Titan rear
7/8″ x 14 thread
1 5/16″ socket

from

$11.29

Product Features:

O-ring for seal housing
Fits Dana Spicer 44 and Toyota 8″ and V6

from

$8.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes