1974 Ford E-200 Econoline Differentials

Product Features:

• Carrier shims for Dana Spicer 60 and 70U

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.

Product Features:

• Forged From Premium Grade 8740 Chrome Moly Steel
• Heat Treated
• Nominally Rated At 200,000 PSI Tensile Strength
• Specially Hardened, Precision Ground Washers
• 0.95″ Underhead Length
• 200,000 PSI
• Sold As A Set

9″ Yukon 3.062″ aluminum case, HD dropout housing with forged caps. The Yukon aluminum dropouts feature a adjuster lock which is offset 90 degrees, offering an uninterrupted bearing cap for higher strenth. Made from A356-T6 aluminum and featuring a through-bolt desgin, this dropout is built for high horsepower & tall tires.Rated up to 1000HP!

Product Features:

• Fits Ford 9″
• 3.062″ carrier race diameter
• A356-T6 aluminum
• Thru-bolt design added strength

Product Features:

• Cross pin bolt for Dana Spicer 60 with c-clip axles

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Trac Loc positraction
• Clutch style positraction
• Aggressive design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

RngPnnInstlKt

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 3.062″. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, pilot bearing, marking compound and brush.

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Adjuster lock bolt 3.062″ & 3.250″ Yukon Ford 9″ Drop Out.

Product Features:

• Side adjuster lock bolt

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion support o-ring
• Fits Ford 9″

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

• Includes three quarts of conventional oil

8″ & 9″ Ford 5-Tab clutches (early Equalock).

Product Features:

• Clutch kit
• Fit Ford 9″ Equa Loc positraction
• 5 outer tabs

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Product Features:

• Trac Loc spring for Ford 8″ and 9″

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

Product Features:

• Nodular iron for added strength
• Thick design
• Durable powder coat finish
• Magnetic drain plug
• Made in USA
• High strength stainless steel fasteners

Set-up bearing (one bearing). HM803146. No return.

Product Features:

• Set up bearing
• Fits HM803146 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Flat side gear without hub for 8″ and 9″ Ford with 28 splines.

Product Features:

• Side gear without hub
• Fits Ford 8″ and 9″ Trac Loc positraction with 28 spline axles

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Replacement crush sleeve for Dana 60, APROX 0.660″ long.

Product Features:

• Crush sleeve for Dana Spicer 60
• 0.660″ tall

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U