1973 Ford E-200 Econoline Differentials

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with oversize Daytona pinion support
• 28 spline
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

Pilot bearing retainer for Ford 9″.

Product Features:

• Pilot bearing retainer for Ford 9″

Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Clutch kit
• Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
• Smooth design
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For use with Trac Loc limited slip
• 1.25″ long

Set-up bearing (one bearing). HM803146. No return.

Product Features:

• Set up bearing
• Fits HM803146 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 3.062″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush, and gasket.

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1957-1981 Ford 10 bolt 9 inch ring gear.

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

9″ Yukon 3.062″ aluminum case, HD dropout housing with forged caps. The Yukon aluminum dropouts feature a adjuster lock which is offset 90 degrees, offering an uninterrupted bearing cap for higher strenth. Made from A356-T6 aluminum and featuring a through-bolt desgin, this dropout is built for high horsepower & tall tires.Rated up to 1000HP!

Product Features:

• Fits Ford 9″
• 3.062″ carrier race diameter
• A356-T6 aluminum
• Thru-bolt design added strength

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 60

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

Yukon forged replacement yoke for Dana 60, stronger than billet, with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60, 70, 70U and 70HD
• 29 spline
• 1350 u-joint size
• 3.625″ snap ring span
• 1.188″ cap diameter
• Outside snap ring design
• U-bolt style

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 31 spline axles
• Trac Loc positraction
• Clutch style positraction
• Street design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.

Product Features:

• Bearing race driver
• Fits HM803110 race
• All steel construction

Product Features:

• Inner oil slinger for Dana Spicer 60

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Trac Loc clutch hub for 9″ Ford with 31 splines.

Product Features:

• Clutch hub
• Fits Ford 9″ Trac Loc with 31 spline axles

Product Features:

• Trac Loc spring for Ford 8″ and 9″

Product Features:

• FORD 9″ CLUTCH PACK KIT NEED ONE PER UNIT

ZIP locker rear switch cover.

Product Features:

• Cover for switch
• Rear

DiffrlPinSupport