from

$36.99

Product Features:

Longer Lasting Performance
Great for Restoration

from

$77.99

Russell’s wide variety of lightweight aluminum adapter fittings allow for the connection of Russell hose ends to almost any component. Adapters are offered in standard thread, metric thread and pipe thread to fit most popular oil pumps, fuel pumps, fuel f

from

$771.99

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

Long Tube Lengths
Long Transition Collectors
Monstrous Low-Mid Range Torque
Keep Top End Horsepower
Provides Finest Fit
Most Durable Design Available

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$367.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched To Performer Intake PN[5486]
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$62.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

from

$471.99

The unique design of these distributors fit tight intake systems while still transferring the high voltage of the MSD racing ignition to the spark plugs. The high voltage carrying capabilities are the result of several features which have been designed into these low-profile distributors. This includes a large diameter cap with wide spaced terminals and an injection molded Rynite rotor with thick vanes to stir up the air inside the cap. The high dielectric Rynite base also prevents arcing to the billet housing. Since these distributors are used primarily in racing applications, an oversized steel shaft is responsible for delivering the sparks. This shaft is QPQ coated for friction reduction and receives guidance from a sealed ball-bearing assembly and an extra long, precision sintered bushing for smooth operation. Note: must be used with an MSD crank trigger and ignition control.

Product Features:

Designed to fit low in the block to clear firewall/intake combos
Supplied w/Bronze Gear
Supplied w/Large Diameter HEI Style Distributor Cap And Rotor
Must Be Used w/An MSD Crank Trigger And MSD Ignition Control
O-ring seals can be installed for oil press. control (Mods only)
Special oil tract improves lubrication to the dist./cam gear
QPQ coated polished steel shaft; guided by sealed ball bearings
Oversized Polished Steel Shaft w/QPQ Coating

from

$60.29

This high quality 1-piece molded rubber oil pan gasket can help stop those annoying leaks. This gasket is for original equipment replacement, high performance drag race and oval track use.

Product Features:

Replaces GM # 12612350
Does Not Fit OEM Dry Sump Engines
Prevents Over tightening
Prevents Torque Loss

from

$119.99

Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:

Replace to Restore Ride Height
Gain Durability
Stronger Than Original Rubber Mounts

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$458.99

Product Features:

Best for the Ultimate in Street High-Performance
Designed Idle to 5500 RPM Street-Driven Power
Dual-Plane High-Rise Intake w/180 deg Firing Order
Produces Incredible Top-End Horsepower
Retains Good Throttle Response and Acceleration
Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock Total Power Package Maximizes Gains

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$84.99

Constructed of durable polyurethane to handle the stress oh high horsepower. Absorbs vibration and lasts longer than rubber Features unique built-in safety lock to keep from separating under high torque loads. Ideal for use on street or strip applications. Complete with grade-8 mounting hardware.

Product Features:

Durable Polyurethane
Absorbs Vibration
Last Longer Than Rubber
Built-In Safety Lock

from

$50.99

Spectre’s Chevrolet water neck fits Chevy V8 engines and features a 90 degree neck with a 360 degree swivel design for a custom look and fit. This water neck has been designed around the OEM specifications, has a height of 2-7/8 inches and has a polished aluminum finish for a lasting look that fits great. This water neck includes the allen bolts and sealing O-ring.

Product Features:

Fits Chevy V8 engines
90 degree neck with a 360 degree swivel design
2-7/8 inch height
Includes sealing O-ring and allen bolts
Polished aluminum finish
Easy to install

from

$288.99

These Mr. Gasket chrome alternators are remanufactured to exceed original equipment specifications for maximum dependability. This 10SI style 80 amp alternator can be used as an original equipment replacement OR as a 1-wire alternator.

Product Features:

Fits Most 1973-1983 GM Vehicles
Bolt Spacing 6.6″
80 Amps
GM 10SI Style Alternator
Chrome Plated Finish
1-Groove V-belt pulley – included
Internal Regulator

from

$110.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$158.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955 to 1985 small block Chevy V8 engines (internally balanced) with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, 10.75 inch bolt pattern, 153 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$230.99

Product Features:

GM 10BL 7.5 &7.625 R/P 3.42 MGP 10 3/8 X 18 LH THRED BLTS, PD=1.438

from

$15.99

Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing.

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing

from

$12.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Lasts Longer
Looks Great

from

$26.99

Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

Product Features:

PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
Precision machined chromoly weights and center plate.

from

$49.49

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

Fits MSD/GM V8 Distributors
Made from high quality materials
Brass terminals
High dielectric properties

from

$788.99

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
O.D.: 1.509″, I.D.: 0.697″
Dual valve springs with damper

from

$42.49

Fits GM (General Motors) Powerglide transmissions with an aluminum case. Chrome plated dipstick that includes O-ring for a positive seal.

Product Features:

Chrome Plated
Includes O-Ring

from

$79.99

Lakewood universal replacement U-joints are fatigue- and wear-resistant, the ultimate in strength. Designed with ultra-durable chrome-nickel-moly alloy cross and caps, and special high-carbon steel and induction heat-treated needle bearings.

Product Features: