1973 Oldsmobile Vista Cruiser Performance Engines

Product Features:

• Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
• NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
• SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
• STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
• DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Mr. Gasket standard intake gasket sets are manufactured from a blend of nitrile rubber and fiber, for excellent sealing and durability. They’re precision die-cut for each specific application to ensure a great fit, and can be custom-trimmed for modified ports where needed. The sets come complete with all necessary seals and block-off plates.

Product Features:

• Designed to ensure excellent sealing
• Provides long lasting durability

Product Features:

• 1.44″x2.44″
• Features Embossed Silicone Bead Around The Intake Ports & Water Openings
• .060″ Thick
• Two Piece Configuration
• End Seals Not Included

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Spectre’s Chevrolet V8 water neck fits 1966 – 1995 Chevy V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes the bolts.

Product Features:

• Fits 1966 – 1995 Chevy V8 engines
• Includes bolts
• Chrome plated
• Designed for OEM fit
• Easy to install
• O-ring/gasket not included

Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:

• Fits Oldsmobile 330, 350, 425 and 455 engines
• Chrome plated
• Bolts included
• Designed for OEM fit
• Easy to install
• O-ring/gasket not included

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Torque Converter – Traveler Converter (SUV and Light Truck) for GM 1968 to 1981 TH350, TH375B APPLICATION: GM 1968 to 1981 TH350, TH375B (6) (will not fit TH-350C) Provides slightly higher stall speed than stock to improve pulling power at low speeds. New

Product Features:

• Ideal For Motor Homes
• Ideal For Towing Applications
• Precision Pump Drive Tube
• Heavy Duty Needle Bearings
• Furnace Brazed

Spectre’s transmission cover for Chevy and GM TH350 transmissions is a great looking cover to help protect your flex plate while on the road. This cover is designed to fit GM and Chevy engines that have the starter on the passenger side. It has a 3-7/8 inch start slot to accommodate the majority of starters. This cover will not work on Pontiac or Oldsmobile engines.

Product Features:

• Polished aluminum
• For GM TH350 transmissions
• For Chevy and GM engines with the starter on the passenger side
• Has a 3-7/8 inch starter slot
• Does not fit Pontiac or Oldsmobile engines
• Easy to install with no special tools or skills required

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 2800-3200 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used

Edelbrock part #2711 Performer Oldsmobile 350 intake manifold is designed for 1964-85, 307-330-350-403 c.i.d. Oldsmobile V8 applications. For non-EGR, the #2711 manifold comes with a universal pad to fit most carburetors with electric chokes. Will fit 198

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type-4150 Style Flange
• 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
• Satin Finish
• Non-EGR

Product Features:

• Best for the Ultimate in Street High-Performance
• Designed for Idle to 5500 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades
• Edelbrock Total Power Package Maximizes Gains

Edelbrock part #7551 Performer RPM Air-Gap Oldsmobile 455 intake manifold is intended for aggressive street/ strip big-block Oldsmobile applications. Designed to optimize horsepower production from 1500 to 6500 rpm, this manifold will perform best with en

Product Features:

• 1500-6500 RPM Range
• Dual Plane Type-4150 Style Flange
• 5.04 in. Front Height, 5.54 in. Center Height, 6.04 in. Rear Height
• Satin Finish
• Non-EGR

Strip Dominator intake manifold square bore carburetor mounting flange. Single plane with isolated plenum. Isolated water cross-over.

Product Features:

• Single Plane With Isolated Plenum
• Square Bore Carburetor Mounting Flange
• Isolated Water Cross-Over
• Power Band 4500-7600 rpm
• Height Front 5.11 in. Rear 5.97 in.
• Port Size 2.05 in. Height 1.22 in. Width
• No Exhaust Heat Crossover Provision
• Ideal For Drag Cars w/Auto Trans.