1973 Ford Mustang Performance and Racing Products

Essential 1973 Ford Mustang Performance and Racing Products

Earls Performance Product – Solo Bleed (Part No.280021ERL)

Solo Bleed

from

$32.59


Product Features:
  • Prevents Air Inclusion
  • Direct Replacement
  • For OE Bleeders
  • One Person Bleeds Safely
  • Without The Mess
  • No Chance Of Air Bubbles
See More

Motive Gear – Differential Carrier (Part No.D3TZ4204A)

Differential Carrier

from

$226.99


Product Features:
  • FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES
See More

Flowmaster Inc. – 40 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound (Part No.942443)

40 Series Muffler, 2.25in Offset Inlet 2.25in Offset Outlet, Non-Reversible, Aggressive Sound

from

$143.99
This two chamber design incorporates Flowmaster’s patented Delta Flow technology. The Delta deflectors generate increased scavenging for better performance and reduced interior sound. Milder exterior tone and reduced interior resonance over Original 40 series. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.
See More

Motive Gear – PRO Gear Lightweight Differential Ring And Pinion – Small Pinion (Part No.F990543SP)

PRO Gear Lightweight Differential Ring And Pinion - Small Pinion

from

$441.99


Product Features:
  • R&P FORD 9″ 5.43, 9310 SMALL PIN 28 SPL. PRO
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1416)

Exhaust Manifold Gasket Set

from

$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Energy Suspension – Strut Rod Bushing Set (Part No.4.7112G)

Strut Rod Bushing Set

from

$31.99
These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:
  • Made from HYPER-Flex Polyurethane
See More

Competition Cams – Magnum/Marine 253/253 Hydraulic Flat Cam for Ford 429,460 (Part No.34-337-4)

Magnum/Marine 253/253 Hydraulic Flat Cam for Ford 429,460

from

$284.99
An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:
  • Best with aftermarket torque converters and 9.5:1 compression.
  • Great high RPM power.
  • Easy on valve train parts.
  • Can be used with mild ratio rocker arms and traditional performance valve springs.
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – Signature Series Valve Covers: Ford 351M-400 & 351C V8, Chrome Steel, Set Of 2 (Part No.4461)

Signature Series Valve Covers: Ford 351M-400 & 351C V8, Chrome Steel, Set Of 2

from

$83.99
The Edelbrock #4461 Signature Series Valve Covers are designed for Ford 351M-400 and 351C V8 applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:
  • Ford 351M-400 & 351C V8
  • Short
  • Chrome Steel
  • Set Of Two
  • Rubber Grommets For Breather
See More

Edelbrock – Performer 351-W Intake Manifold for S/B Ford 351 Windsor (Part No.2181)

Performer 351-W Intake Manifold for S/B Ford 351 Windsor

from

$382.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Stock Replacement
  • 50-State Street Legal
See More

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Super Intake Manifold Bolts

from

$43.99
Super Intake Manifold Bolts

Spectre – Spectre Replacement Air Filter (Part No.HPR3300)

Spectre Replacement Air Filter

from

$31.49
Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use.

Product Features:
  • High performance and high air flow filter
  • Filter media is non-woven synthetic and pre-dyed
  • Replaces stock air filter
  • Easy to install with no special tools or skills required
  • Reinforced with a steel mesh
See More

MSD Ignition – Starter; Small Block Ford 289; 302; 351W 5.0L (Part No.5090)

Starter; Small Block Ford 289; 302; 351W 5.0L

from

$438.99
Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:
  • Mount Can Be Clocked To Assist In Mounting
  • Downsized design helps clearance issues w/oil pans and exhaust
  • Ball bearing supported armature and pinion gear
  • 3 Hp Motor Provides Power For High Compression Engines
  • Gear reduction of 4.4:1 improves torque for great cranking
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Edelbrock – Front Timing Cover Gasket Set #6991 For Small-Block Ford, With Front Seal (Part No.6991)

Front Timing Cover Gasket Set #6991 For Small-Block Ford, With Front Seal

from

$28.99
Available in kits including front cover gasket, crankshaft seal, fuel pump and water pump gasket or including cover gasket and front seal.

Product Features:
  • Timing Cover Gasket And Oil Seal Kit
See More

Mr. Gasket – Oil Pan Bolt Kit (Part No.6087)

Oil Pan Bolt Kit

from

$30.19
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:
  • Ideal For Tight Spaces
  • Serrations Prevent Loosening
  • Flange Distributes Pressure
  • Zinc Plated Bolts
  • Grade 5 Material
  • Easy Installation
See More

Edelbrock – Performer RPM Series fuel pump is for 289-351W Ford (Part No.1725)

Performer RPM Series fuel pump is for 289-351W Ford

from

$177.99
Product Features:
  • Mechanical Operation
  • Fuel Sending Unit Not Included
  • For Small-Block 289-351 Ford Engines
  • In Tank Mounting Type
  • 110 GPH
See More

Mr. Gasket – Chrome Distributor Hold-Down Clamp (Part No.9860)

Chrome Distributor Hold-Down Clamp

from

$13.29
Chrome plated steel. Includes hold-down bolt or stud. Holds the distributor in place for accurate timing. Serrated bottom prevents the distributor from turning.

Product Features:
  • Rolled Edges For Strength
  • Ideal For Magnetos
  • Ideal For Ignition Distributor
See More

Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)

Super Stock Replacement Coil for Improved Performance, Starting, and Power

from

$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:
  • 42000 Volts
  • Effective To 6500 RPM
  • Quicker Starting
  • Improved Throttle Response
  • Higher RPM Power
  • Can Finished In Yellow
See More

Energy Suspension – Heavy Duty Shackle Set (Part No.4.2135R)

Heavy Duty Shackle Set

from

$161.99
Product Features:
  • Reduces Wheel Hop in Acceleration
  • Prevents Shudder under Braking
  • Delivers Greater Handling Control
  • Great for Vehicles with High Performance Tires
  • Great for Vehicles with Horsepower Upgrades
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Edelbrock – SBF Timing Cover, 86-93 5.0L & 88-Later 351W W/ Reverse Rotation Pump (Part No.4251)

SBF Timing Cover, 86-93 5.0L & 88-Later 351W W/ Reverse Rotation Pump

from

$225.99


Product Features:
  • Most Complete Fuel Injection System Available
  • Bolt On Performance
  • Ready To Run Out Of The Box
  • Easy Connection And Quick Removal Connector
See More

Mr. Gasket – Alternator Bracket (Part No.5185)

Alternator Bracket

from

$38.49
These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated for lasting beauty. Similar in design to original equipment units.

Product Features:
  • Fits Small Block Ford 1965-’69 – OEM Style
  • Polished To High Luster
  • Chrome Plated For Lasting Beauty
See More

Energy Suspension – Tie Rod Dust Boot (Part No.9.13102G)

Tie Rod Dust Boot

from

$5.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:
  • Easy to Install
  • Superior Material
  • Saves Your Tie Rods
  • Lasts Longer
  • Looks Great
See More

Energy Suspension – Leaf Spring Bushing Set (Part No.4.2101G)

Leaf Spring Bushing Set

from

$78.99
Adds a dramatic amount of performance and durability to any vehicle, cars, trucks and SUVs. Helps the vehicle be in control – when maneuvering through turns, during standing start accelerations, braking, even over bumps and berms. Made of Energy’s Hyper-Flex performance polyurethane which lasts 5 -10 times longer than conventional rubber components.

Product Features:
  • Made of Superior Hyper-Flex+ Material
  • Adds Dramatic Amount of Performance/Durability
  • Helps Vehicle Be in Control
  • Allows the Suspension to Function Properly
See More

B & M – Torque Converter, Tork Master 2000 (Part No.40427)

Torque Converter, Tork Master 2000

from

$349.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

MSD Ignition – Distributor; Ford V8; 351C; 460 (Part No.8580)

Distributor; Ford V8; 351C; 460

from

$438.99
MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:
  • CNC machined billet aluminum housing and Dupont Rynite base
  • No CARB Exemption Order Number
  • Supplied w/Cap-A-Dapt and rotor (accepts MSD socket style caps)
  • Must Be Used w/An MSD Ignition Control
  • Mech. advance assem. can be locked out for crank trigger systems
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
  • Advance plate and weights are fine blanked from chrome moly steel
  • QPQ coated for friction reduction
  • QPQ coated polished steel shaft; guided by sealed ball bearings
  • Maintenance-free magnetic pickup and precision reluctor
  • Creates stable trigger signals throughout the rpm range
See More

Accel – Contact And Condenser Kit (Part No.8203)

Contact And Condenser Kit

from

$79.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:
  • High Performance Points and Condenser
  • With Integral Conductor
See More

Popular 1973 Ford Mustang Performance and Racing Products Categories

1973 Ford Mustang Performance and Racing Products

You count on your 1973 Ford Mustang to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 205 Performance and Racing Products ranging in price from $5.99 to $999.99, you’re sure to find everything you need for your 1973 Ford Mustang.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 24 different brands like Accel, Mr. Gasket, and Edelbrock. 1973 Ford Mustang Performance and Racing Products start as low as $5.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 2,781 extensive product reviews on 1973 Ford Mustang Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Water Neck with 3.8 stars and Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines with 4.8 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1973 Ford Mustang below to get started!

Top-Rated Performance and Racing Products Brands For Your 1973 Ford Mustang

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1973 Ford Mustang running right for years to come. In our inventory you’ll find brands like Accel, Mr. Gasket, Edelbrock, and even more.

Popular MSD Ignition Performance and Racing Products

You’ll find popular MSD Ignition brand products across Performance Distributors. All are waiting to get your 1973 Ford Mustang back on the road. Some of the top-rated MSD Ignition products in these categories are:
Distributor Gear; Ford; 302; Bronze
from $83.39
(1)
Distributor Gear; Ford; 302; Bronze
Performance Distributor Components

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1973 Ford Mustang, and some of our most reviewed Edelbrock parts include:

FAQs for 1973 Ford Mustang Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1973 Ford Mustang?

Out of 205 Performance and Racing Products for the 1973 Ford Mustang, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets

What are the top-rated 1973 Ford Mustang Performance and Racing Products?

Top-rated Performance and Racing Products for your 1973 Ford Mustang based on customer reviews/ratings are:
Water Neck
from $19.99
(12)
Water Neck
“FINALLY… first time not having to re-do flimsy paper gaskets. Aside from thicker cork gasket, O ring is only way to go !”
Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines
from $228.99
(4)
Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines
“Like the distributor so much, that I am contemplating on replacing the Mallory Distributor on the other car with one.”
High Perf. Full-Flow Lube Spin-on
from $16.99
(4)
High Perf. Full-Flow Lube Spin-on
“Filter size for my boat. OMC 460. works fine. HP filters have a bypass so that clogs do not cause the engine to starve for oil… important for HP eng”