1973 Ford E-100 Econoline Performance Engines

Essential 1973 Ford E-100 Econoline Performance Engines

Mr. Gasket – Precision Timing Tape (Part No.1594)

Precision Timing Tape

from

$21.79
Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:
  • 6 3¿8″ diameter
  • 6 3┐8″ diameter
  • 289-302-351 cu. in.
  • Increased Performance
  • Set Valve Lash At Proper Time
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5870)

Ultra Seal: Valve Cover Gasket Set

from

$36.49
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.

Product Features:
  • Manufactured from high-density cork /rubber blend gasket material
  • A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
  • Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
  • For OE replacement, high performance street, drag race and oval track
  • .187″ thick
  • Handles Ex Flange Pressure
  • Forms Leak Proof Seal
  • Black Latex Coating
See More

B & M – Torque Converter, Tork Master 2400 (Part No.50441)

Torque Converter, Tork Master 2400

from

$450.99
A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength. Due to torque converter co

Product Features:
  • New Precision Pump Drive Tube
  • Pressure Tested
  • Fully Balanced
  • Needle Thrust Bearing
  • New Thrust Washer
See More

Edelbrock – Complete Sure Seat Valve Spring Kit for Ford 289-302 & 351W V8 (Part No.5896)

Complete Sure Seat Valve Spring Kit for Ford 289-302 & 351W V8

from

$125.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • Complete Kit: Includes Retainers And Locks
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Includes Superior Quality Steel Retainers
  • Includes 7 deg. Heat-Treated Valve Stem Locks
  • Retainers and Locks Black Oxide Coated
  • Dyno Tested And Street Proven
  • Great Match to Edelbrock Camshaft Kit
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 7 Piece Set (Part No.1240)

Lower Intake Manifold Gasket Set: 7 Piece Set

from

$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
  • Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
  • 1970-82; w/2 Bbl. Cylinder heads
  • Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Water Pump for Small-Block Ford 351W in Black Finish (Part No.88433)

Water Pump for Small-Block Ford 351W in Black Finish

from

$358.99
Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:
  • Standard Impeller Rotation
  • 0.625 in. Pilot Shaft
  • 0.750 in. Ball/Ball Bearing
  • 5.70 in. Block To Hub Height
  • Black Finish
See More

Competition Cams – Xtreme Energy 218/224 Hydraulic Flat Cam (Part No.31-238-3)

Xtreme Energy 218/224 Hydraulic Flat Cam

from

$257.99
HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.

Product Features:
  • HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.
  • 262/270 Advertised Duration, 218/224 Duration @ .050″, .493″/.500″ Lift, 110 Lobe Separation
  • Valve spring upgrade required
  • 289-302 Firing Order
See More

Weiand – Hi-Ram; Intake Manifold Top (Part No.1915)

Hi-Ram; Intake Manifold Top

from

$351.99


Product Features:
  • Top Only
See More

Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)

ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST

from

$237.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:
  • Cost effective aluminum construction provides superior strength to weight ratio
  • Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
  • Durable design increases valve lift while withstanding the rigors of moderate race use
  • Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
See More

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6683)

Ultra Seal: Oil Pan Gasket

from

$59.19
High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:
  • Steel core provides rigidity, durability and prevents gasket push out
  • Molded rubber coating seals minor irregularities in pan surface
  • One piece design is easier to install and even less prone to leak
  • Direct replacement suitable for all uses – street, racing, heavy duty
  • Include both gasket and new oil pan bolts
  • No Cork Particles
  • Easy Removal For Disassembly
See More

Edelbrock – Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90 Polished (Part No.603719)

Performer Small-Block Ford 5.0L/ 5.8L Cylinder Head 1.90 Polished

from

$975.99
Product Features:
  • Complete Single For Hydraulic Flat Tappet
  • 60cc Combustion Chamber Volume
  • 170cc Intake/60cc Exhaust Runner Volume
  • 1.9 in. Intake/1.6 in. Exhaust Valve Diameter
  • 0.625 in. Deck Thickness
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Performer Series Retainer (Qty 16)

from

$100.99
Product Features:
  • Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

289-302 Ford Head Bolt Kit

from

$107.99


Product Features:
  • Highest Quality Head Bolts
  • Cold-Formed/Heat Treated
  • Ensures Molecular Integrity
  • Reduced Diameter Bolt Heads
  • Hardened/Parallel-Ground Washers Included
  • Rated At 170000 psi
  • Manufactured By ARP
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1963)

Rear Main Seal Gasket

from

$42.49
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.30)

Rear Main Seal Gasket

from

$42.49
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It is a direct replacement for a factory one-piece rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs that leaky rear main seal
  • Direct replacement for stock one-piece seal
  • Silicone rubber to withstand extreme oil temperatures
  • Injection molded for precise fit
See More

Mr. Gasket – Cam Change Gaskets (Part No.4410)

Cam Change Gaskets

from

$63.09
If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:
  • Contains all the gaskets needed to change out your camshaft
  • Fuel Injector O-Ring Not Included
  • Meets Performance Standards
See More

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Pushrod Set for Small Block Ford 289-302

from

$210.99
Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Pushrod Set for Ford 351W (Part No.9659)

Pushrod Set for Ford 351W

from

$190.99
Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:
  • 7.7 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Super Intake Manifold Bolts

from

$43.99
Super Intake Manifold Bolts

Mr. Gasket – Intake Manifold Bolts (Part No.958G)

Intake Manifold Bolts

from

$19.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers

Product Features:
  • Hex Head
  • Zinc Plated
  • Ideal For Minimal Space
  • 12-Point Head And Flange
  • Zinc Plated For Protection
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1018)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$49.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1013)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$58.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-2)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$55.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Edelbrock – Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Ford (Part No.7365)

Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Ford

from

$186.99
Product Features:
  • Head: 4.500″ Bore/0.048″ Thick/12.5cc Vol.
  • Intake: 1.98″x2.26″ Port/.060″ Thick
  • Exhaust: 1.50″x2.10″ Port
  • 5/16″ Valve Cover
  • Multi Piece Configuration
See More

Edelbrock – Cylinder Head Gasket Set for Ford (Part No.7314)

Cylinder Head Gasket Set for Ford

from

$126.99
Product Features:
  • 4.5 in. Cylinder Bore Diameter
  • 0.048 in. Thickness
  • 12.5cc Volume
  • Gray Color
  • Two Piece Configuration
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$51.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

1973 Ford E-100 Econoline Performance Engines

Maybe you’re in the middle of a full rebuild of that 1973 Ford E-100 Econoline. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 45 different Performance Engines in our inventory ranging from $19.99 to $1,035.99. That means you can find the exact parts or products you need to keep that 1973 Ford E-100 Econoline running smoothly.

Performance Engines are only as good as their brand. We stock 5 different brands to make sure you have plenty of trusted parts to choose from for your 1973 Ford E-100 Econoline. Mr. Gasket, FEL-PRO Performance, and Edelbrock are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1973 Ford E-100 Econoline, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 164 reviews in this category, some of the top rated parts include 289-302 Ford Head Bolt Kit with 2.0 stars and ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST with 1.0 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1973 Ford E-100 Econoline rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1973 Ford E-100 Econoline Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1973 Ford E-100 Econoline demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your E-100 Econoline the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular FEL-PRO Performance Performance Engines

We carry FEL-PRO Performance parts in our stock across Performance Engine Intake Manifold Gaskets and Performance Engine Valve Cover Gasket Sets categories, plus more. For a 1973 Ford E-100 Econoline, our most popular FEL-PRO Performance Performance Engines include:
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
Engine Valve Cover Gasket Set
from $46.99
(1)
Engine Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $51.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

Top 1973 Ford E-100 Econoline Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1973 Ford E-100 Econoline. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
Ultra Seal: Valve Cover Gasket Set
from $36.49
(3)
Ultra Seal: Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets
Intake Manifold Bolts
from $19.99
(1)
Intake Manifold Bolts
Performance Intake Manifold Hardware

FAQs for 1973 Ford E-100 Econoline Performance Engines

What are the most purchased Performance Engines for the 1973 Ford E-100 Econoline?

Out of 45 Performance Engines for the 1973 Ford E-100 Econoline, the most popular in our inventory are:
Intake Manifold Gasket for 1963-1996 Small-Block Fords
from $28.99
(1)
Intake Manifold Gasket for 1963-1996 Small-Block Fords
Performance Engine Intake Manifold Gaskets
Performer-Link Adjustable True-Roller Timing Chain Set
from $67.99
This product is not rated
Performer-Link Adjustable True-Roller Timing Chain Set
Performance Engine Timing Sets and Components
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
from $38.49
This product is not rated
Ultra Seal: Harmonic Balancer Bolt/Washer Kit
Performance Engine Harmonic Balancers

What are the top-rated 1973 Ford E-100 Econoline Performance Engines?

Top-rated Performance Engines for your 1973 Ford E-100 Econoline based on customer reviews/ratings are:
289-302 Ford Head Bolt Kit
from $107.99
(7)
289-302 Ford Head Bolt Kit
“Great quality bolts. They include thread locker. Would definitely recommend to anyone replacing their heads.”
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
from $237.99
(1)
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
“These things break very easy. Not a big fan of the soft brass when trying to install them with the screwdriver head they use. Change it hex and it woy”
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
from $111.99
(1)
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
“THIS WAS NOT A COMPLETE KIT!ONLY GOT VALVE SPRINGS!!!”