1971 Ford E-100 Econoline Differentials

Product Features:

• NODULAR HOUSING 9″ FORD 3.25″ BORE

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Ford 8″
• 8.00″ ring gear diameter
• 25 spline pinion
• 10 ring gear bolts
• 4.11 ratio

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

Yukon Carrier Installation Kits are a convenient and low-cost solution for carrier changes in cases where one is upgrading to a positraction limited slip differential, a mechanical locker, or an air operated locker. These kits contain carrier bearings and races and a carrier shim kit.

Product Features:

• Fits Ford 8.8″
• Includes carrier bearings and races and “super” carrier shim kit

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Anodized purple
• 6061 aluminum
• Larger inner pinion bearing reduces gear deflection under high load
• Fits Ford 9″ with 28 spline pinion
• Anodized purple

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Complete shim kit for Dana Spicer 44

Product Features:

• FORD 9″ CLUTCH PACK KIT NEED ONE PER UNIT

Union 76 gear oil is a conventional non-synthetic 80W90 formulation designed for all types of differentials.

Product Features:

• Includes three quarts of conventional oil

Manufactured with premium-grade steel, National taper bearing sets feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

For vehicles that are driven daily, the Power Trax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Power Trax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Power Trax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Power Trax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds.

Product Features:

• The Power Trax Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Power Trax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Power Trax lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Power Trax offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Power Trax ia an Extreme Traction System

Worn or damaged differential end yoke causing driveline Vibrations- This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft for Ford 8.8″
• 0.875″ diameter

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• For Dana 25, 27, 30, 44, 50, and 53 differentials
• Fits 02820 race
• Ensures accurate installation of bearing races

Conversion bearing for small bearing Ford 9″ axle in large bearing housing.

Product Features:

• Cover gasket
• Fits Dana Spicer 44

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Oil baffle for Dana Spicer 44

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• 1.0″ long
• 3/8″-16
• Pinion support bolt for Ford 8″ and 9″ differentials

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. You can count on Yukon to fulfill all your differential small parts needs.

Product Features:

• Side gear with hub
• Fits Ford 8″ and 9″ standard open differential and Trac Loc positraction with 31 spline axles

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Yukon Gear & Axle spider gear kits feature higher quality materials and better manufacturing techniques than OEM to ensure a longer lasting spider gear set. Kit delivers everything needed for a complete and proper spider gear set replacement.

Product Features:

• Spider gear kit
• Fit Ford 8″ and 9″ open differential with 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pins and spider gear thrust washers.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or GM and Chrysler 11.5″ 1-ton applications
• Works with an impact gun to safely and easily remove carrier bearings
• Comes with a handy bench-top stand
• For 1-ton applications shop Yukon part YT P22

Yukon Gear & Axle dropouts are heavy duty. They feature upgraded nodular iron construction and a larger-than-OEM design to provide unrivaled strength and reliability in racing and off-road applications.

Product Features:

• Side adjuster lock bolt