1971 Ford Bronco Differentials

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

Product Features:

• Cover gasket
• Fits Dana Spicer 44

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

• Fits 2009 and down Ford 8.8″
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits reverse rotation Dana Spicer 44
• 8.50″ ring gear diameter
• 26 spline pinion
• 10 ring gear bolts
• 5.13 ratio

Product Features:

• Complete shim kit for Dana Spicer 30 front

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

Product Features:

• DANA 44 R/P 3.92 STD MG

Yukon Trac Loc positraction, Ford 8.8″, 31 spline, with Carbon Fiber clutches.

Product Features:

• Trac Loc positraction carrier case
• Includes spider gears
• Fits Ford 8.8″ with 31 spline axles
• Carbon fiber clutches

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

Yukon standard open spider gear kit for 8.8″ Ford with 31 spline axles and 7/8″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
• 0.875″ cross pin shaft diameter

9″ FORD 35Spline SPOOL 30deg (EXCL M.WLMS) 2-3/16″ DECK , 2″ Journal .

Product Features:

• Fits Ford 9″ with 35 spline axles
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Castrol® Transmax® ATF/CVT Universal is a premium full-synthetic transmission fluid engineered for exceptional performance in both traditional step-shifting automatic transmissions and modern continuously variable transmissions (CVTs). Featuring Castrol Smooth Drive® Technology, it ensures enhanced friction durability for seamless gear shifts and superior high-temperature protection to resist oxidation. This advanced formulation offers unmatched protection against copper corrosion, extending the life of your transmission system. Its broad compatibility covers a wide range of ATF and CVT applications, including Dexron VI, Mercon LV, Toyota WS, Honda DW-1, Nissan Matic S, and many more, making it ideal for diverse vehicle types, including hybrids. Designed to improve workshop efficiency and simplify inventory management, this fluid is a versatile solution for professional mechanics and DIY enthusiasts alike. Packaged in a convenient 1-gallon size, it delivers outstanding value and reliability for maintaining optimal transmission performance.

Product Features:

• Enhanced friction durability for smooth transmission performance
• Superior high temperature protection to effectively resist oxidation
• Unsurpassed protection against copper corrosion
• Broad scope of vehicle applications improves workshop efficiency and inventory management
• ATF Applications: Dexron VI (Dexron III, Dexron), Mercon LV (Mercon SP, Mercon V, Mercon), JASO 1A (03), JASO 1A LV (13), Toyota T IV, Toyota T III, Toyota WS, Honda/Acura DW 1/Z 1, Nissan Matic D, Matic J, Matic S, Hyundai/Kia SP IV, SP III
• ATF Applications: Mazda ATF M-V, M-III, FZ, Mitsubishi SP IV, SP III, IIM, II, PA, J3, VW/Audi (6, 8 & 9 speed automatics), BMW/Mini (6, 8 and 9 speed automatics), Jaguar/Land Rover (6, 8 & 9 speed automatics), Porsche (6, 8 & 9 speed automatics)
• ATF Applications: Volvo (6, 8 and 9 speed automatics), Volvo Transmission Oil 97342, AT102, Mercedes-Benz (7 and 9 speed automatics)
• CVT Applications: Toyota CVT Fluid TC, Toyota CVT Fluid FE , Nissan CVT Fluid NS-1, Nissan CVT Fluid NS-2, Nissan CVT Fluid NS-3, Subaru i-CVT Fluid, Subaru i-CVT FG, Subaru Lineartronic High Torque Chain CVTF, Honda HCF-2

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

• Trac Loc spring for Ford 8″ and 9″

Yukon Extra HD 3.250″ nodular Iron dropout for Ford 9″ with load bolt. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Load bolt design prevents gear deflection under heavy loads. Rated up to 1400HP!

Product Features:

• Fits Ford 9″
• 3.250″ carrier race diameter
• Nodular iron for added strength
• Load-bolt design reduces ring gear deflection under high horsepower

Pinion seal for 7.5″, 8.8″, and 9.75″ Ford, and also 1985-’86 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 7.5″, 8.8″ and some 9.75″
• 2.785″ O.D.

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Ford 8.8″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Ford 8.8″
• Includes carrier bearings and races and “super” carrier shim kit

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Bearing race driver for Dana 44 front (TK 02820). No return.

Product Features:

• Bearing race driver
• Fits 02820 race
• All steel construction

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Product Features:

• Carrier shim kit for Dana Spicer 30 with 30 spline axles

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread