1971 Dodge D300 Pickup Drivetrains
More 1971 Dodge D300 Pickup Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1971 Dodge D300 Pickup, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1971 Dodge D300 Pickup Drivetrains
Yukon Gear – Replacement Baffle For Dana 70 & 70HD (Part No.33003)
Yukon Gear – Pinion Install Kit For Dana 60 Rear Differential (Part No.13032)
from
$295.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 rear
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)
from
$233.99
Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 29 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
Yukon Gear – Cross Pin Bolt (Part No.33067)
from
$6.99
Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.
Product Features:
See More
Product Features:
- Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS
Yukon Gear – Minor Install Kit For Dana 70-HD & Super-70 Differential (Part No.12028)
from
$169.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.
Product Features:
See More
Product Features:
- Fits Dana Spicer 70HD
- Included are a pinion seal, complete shim kit, marking compound and brush.
Yukon Gear – Replacement Positraction Internals For Dana 60 And 70 With 35 Spline Axles (Part No.16008)
from
$832.99
Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Clutch kit
- Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
- Smooth design
- Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.
National – Bearings (Part No.28521)
from
$26.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Powertrax – Grip PRO Traction System (Part No.GT436035)
from
$596.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Yukon Gear – The Carrier Bearing Puller (Part No.56034)
from
$689.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
- Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications
Motive Gear – Ring Gear Bolt (Part No.14066913)
Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)
from
$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 60, 70 and 80
- 3/8″
Driveworks – Oil Seal (Part No.S-482163N)
National – Bearings (Part No.HM88510)
from
$14.29
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Dana 60 & Dana 70 Power Lok Case Bolt (Part No.33236)
from
$7.99
Dana 60 & Dana 70 Power Lok case bolt.
Product Features:
See More
Product Features:
- Power Lok case bolt for Dana Spicer 60 and 70
- 7/16 x 14 thread
- 3.5″ long
- 9/16″ hex head
Yukon Gear – Replacement Outer Oil Slinger For Dana 60, 70, 70U & 70HD (Part No.33019)
Yukon Gear – Positraction Clutch Guide (Part No.33352)
from
$8.99
Positraction clutch guide.
Product Features:
See More
Product Features:
- Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
- Compatible with Dura Grip positractions only
Yukon Gear – Zip Locker Bulkhead Fitting Kit (Part No.34000)
from
$36.99
Product Features:
See More
- Bulkhead fitting kit
- Includes bulkhead fitting, outer fitting and o-ring
Victor Reinz – Drive Axle Shaft Flange Gasket (Part No.71-13861-00)
from
$3.29
With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.
Product Features:
See More
Product Features:
- Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.
National – Multi Purpose Bearing (Part No.HB-88107-A)
from
$44.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)
from
$9.99
Chrysler 8.75″ (coarse spline) pinion nut washer.
Product Features:
See More
Product Features:
- Pinion nut washer
- Fits Chrysler 8.75″ with 10 spline pinion
Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (Part No.615-072.1)
from
$3.49
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Yukon Gear – 9.25" Pinion Gear Thrust Washer (Part No.33274)
from
$12.99
9.25″ pinion gear thrust washer.
Product Features:
See More
Product Features:
- Pinion gear thrust washer for Chrysler 9.25″ rear
Yukon Gear – Replacement Carrier Shim Kit For Dana 70 & 70HD (Part No.55019)
Yukon Gear – Pinion Seal For 8.75" Chrysler Or For 9.25" Chrysler With 41 Or 89 Housing (Part No.30121)
from
$13.99
Pinion seal for 8.75″ Chrysler or for 9.25″ Chrysler with 41 or 89 housing.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Pinion seal
- Fits Chrysler 8.75″ with ’41’ and ’89’ case housings and 2000 and down Chrysler 9.25″
Neapco – Universal Joint (Part No.2-1175)
Yukon Gear – Replacement Pinion Depth Shims For Dana 70HD, Dana 70, Ford 10.25" & 10.5" (Part No.55013)
from
$16.99
Product Features:
See More
- Pinion depth shims for Dana Spicer 70 and 70HD, Ford 10.25″ and 10.5″
Driveworks – Tapered Roller Bearing (Part No.S-LM-603011)
Motive Gear – Differential Carrier Shim Kit (Part No.1106)
Popular 1971 Dodge D300 Pickup Drivetrains Categories
1971 Dodge D300 Pickup Drivetrains
You count on your 1971 Dodge D300 Pickup to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 250 Drivetrains ranging in price from $3.29 to $1,487.99, you’re sure to find everything you need for your 1971 Dodge D300 Pickup.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 15 different brands like National, Yukon Gear, and Anchor. 1971 Dodge D300 Pickup Drivetrains start as low as $3.29!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 869 extensive product reviews on 1971 Dodge D300 Pickup Drivetrains. Some of the top-rated Drivetrains products we carry are Tapered Roller Bearing with 5.0 stars and DIFFERENTIAL GASKET with 3.0 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1971 Dodge D300 Pickup below to get started!
Top-Rated Drivetrains Brands For Your 1971 Dodge D300 Pickup
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1971 Dodge D300 Pickup running right for years to come. In our inventory you’ll find brands like National, Yukon Gear, Anchor, and even more.
Popular MOOG Driveline Products Drivetrains
You’ll find popular MOOG Driveline Products brand products across Universal Joints. All are waiting to get your 1971 Dodge D300 Pickup back on the road. Some of the top-rated MOOG Driveline Products products in these categories are:
Top-Rated National Drivetrains
If National are what you’re looking for, our inventory holds plenty. We stock National brand Drivetrains for your 1971 Dodge D300 Pickup, and some of our most reviewed National parts include:
FAQs for 1971 Dodge D300 Pickup Drivetrains
What are the most purchased Drivetrains for the 1971 Dodge D300 Pickup?
Out of 250 Drivetrains for the 1971 Dodge D300 Pickup, the most popular in our inventory are:
What are the top-rated 1971 Dodge D300 Pickup Drivetrains?
Top-rated Drivetrains for your 1971 Dodge D300 Pickup based on customer reviews/ratings are:
from
$8.49
(7)
Tapered Roller Bearing
“Nice to find them in stock. Fit well and got my SUV up and back on the road quickly”
