Name: Intake Manifold Gasket for 1963-1996 Small-Block Fords
Brand: Edelbrock
SKU: 72208
Price: 165.99 USD

from

$165.99

Available in different sizes for many different vehicle models/years. Clean positive seal. Embossed silicone bead surrounding the port. Matched to manifolds and cylinder heads. In the early days of the automotive performance industry, you either ran what

Product Features:

Clean positive seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads
Fits 1963-96 289/302/351W Engines
10-Pack Of Gaskets

from

$443.99

New qwik-tune adjustable secondary air valve. Optional single or dual fuel inlet. Distinctive black accented hardware. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkag

Product Features:

New Qwik-Tune Adjustable Secondary Air Valve
Optional Single Or Dual Fuel Inlet
Distinctive Black Accented Hardware
No Gaskets Below Fuel Level to Prevent Leakage
Metering Rod/Step Up Springs Can Be Changed Easily
GM/AMC-Style Throttle Linkage
Exclusive 12 Month Complete Satisfaction Warranty

from

$360.99

RngPnn

from

$72.39

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

Helically wound conductor suppresses electro and radio noise
Kevlar core combination for great strength and durability
Heavy Duty Terminals For Secure Connection
8mm silicone and synthetic jacket resists heat and abrasion
500 Ohms/ft. Resistance For Improved Spark Delivery And Power
Silicone Boots Protect Against High Exhaust Temps

from

$117.99

Designed to be used with late model Ford waste spark ignition systems. 83:1 turns ratio and lower primary resistance produce high voltage output. Secondary towers designed for snap on spark plug terminals. Primary terminals require Ford style connector. Carb O.E. approved.

Product Features:

Designed to use w/late model Ford waste spark ignition systems
83:1 turns ratio
Lower Primary Resistance Produces High Voltage Output
Secondary towers designed for snap on spark plug terminals
Primary terminals require Ford style connector

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$67.99

The B&M Shift Improver kit, is the easiest way to get the performance you want out of your transmission. A few simple modifications and your transmission will shift fast, firm and live longer.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$368.99

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

Good blend of efficiency and performance.
Perfect choice for performance street rebuilds.
Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

from

$60.99

Product Features:

Valve Cover Gasket

from

$59.19

High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:

Steel core provides rigidity, durability and prevents gasket push out
Molded rubber coating seals minor irregularities in pan surface
One piece design is easier to install and even less prone to leak
Direct replacement suitable for all uses – street, racing, heavy duty
Include both gasket and new oil pan bolts
No Cork Particles
Easy Removal For Disassembly

from

$381.99

The Edelbrock #4160 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. They are made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

Small Block Ford 221-351W 62-95
Tall
Polished Aluminum
Set Of Two

from

$269.99

The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.

Product Features:

Ideal As Column Shift Replacement
Includes Neutral Safety Switch
Includes Black T-Handle
Backup Light Not Available
Includes 5 ft. Cable and Hardware
Includes Boot and Plate

from

$26.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$1157.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street fuel injected applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$73.29

Mallory distributor gears are precision machined from alloy steel in our factory to exact original equipment specs. For use with cast flat tappet hydraulic/mechanical cams and austempered ductile iron roller cams.

Product Features:

Replacement Distributor Gear

from

$38.49

Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Thick parallel ground washer provides more accurate, uniform torque
Hex Prevents Socket Slippage
Accurate And Uniform Torque
Black Plated Finish

from

$226.99

Product Features:

FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

from

$100.99

Product Features:

Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$630.99

Utilizes late model alternator and A/C bracket mounting provisions. Has vacuum taps off Manifold runners. Uses cable bracket P/N 20-101 for GM 700R4 transmission. Extra installation hardware included.

Product Features:

Dual Plane Design
Front Height 3.5 in.
Rear Height 4.18 in.

from

$691.99

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

Product Features:

Equipped w/Steel Gear
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Nylon pads ensure smooth operation of the advance weights
Advance weight pins are staked and tig welded to the plate
Mech. advance assem. can be locked out for crank trigger systems

from

$79.99

Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:

High Performance Points and Condenser
With Integral Conductor

from

$29.99

These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:

Made from HYPER-Flex Polyurethane

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features: