from

$292.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 8.75″ ’41’ case
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$301.99

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Chrysler 8.25″ open differntial with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$289.99

Yukon round companion flange for Jeep Liberty rear, Chrysler 8.25″. Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.25″
27 spline
Round companion flange

from

$339.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Chrysler 8.75″ ’41’ case housing with LM104912 carrier races
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$93.99

Product Features:

Fits Chrysler 9.25″ rear
Steel

from

$261.99

Product Features:

Standard open carrier case
Fits 2009 and down Chrysler 9.25″ rear
Does not include spider gears

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$64.99

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

Side adjuster for Chrysler 9.25″ rear

from

$231.99

A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.

Product Features:

Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
Durable construction – designed and manufactured to strict specifications for reliable performance
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$564.99

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

Fits Chrysler 8.75″
’89’ case design
Nodular iron for added strength

from

$342.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$84.99

8.25″ Chrysler notched cross pin shaft for standard open carriers. (0.801″ diameter). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers, or with factory Trac Loc positractions.

Product Features:

Cross pin shaft
Fits Chryler 8.25″
0.801″ diameter
Notched
Not compatible with Spartan Lockers or Lock Rights

from

$333.99

Yukon standard open spider gear kit for 9.25″ Chrysler with 31 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Chrysler 9.25″ rear with open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$28.99

Product Features:

MINI INSTALL KIT CHRYSLER 9.25 9 1/4″

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$177.99

Product Features:

Clutch kit
Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
Smooth design

from

$98.99

Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.

Product Features:

Side gear thrust washer kit
Fits Chrysler 8″ and 9.25″

from

$9.99

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

Pinion nut washer
Fits Chrysler 8.75″ with 10 spline pinion

from

$9.99

Product Features:

Cross pin bolt for Dana Spicer 60 with c-clip axles

from

$39.99

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

Pinion depth shim kit for Toyota 7.5″, 8″ and V6

from

$829.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Chrysler 9.25″ rear
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$67.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$8.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$41.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

1969 Dodge Monaco Differentials

More 1969 Dodge Monaco Differentials

Essential 1969 Dodge Monaco Differentials

Yukon Gear – Pinion Install Kit For Chrysler 8.75" (#41) Differential (Part No.13005)

Yukon Gear – Standard Open Spider Gear Kit For ’96 And Older 8.25" Chrysler With 27 Spline Axles (Part No.16002)

Yukon Gear – Round Companion Flange For Jeep Liberty Rear, Chrysler 8.25" (Part No.41120)

USA Standard Gear – Master Overhaul Kit For Chrysler 8.75" #41 Housing With LM104912/49 Carrier Bearings (Part No.37089)

Yukon Gear – Steel Cover For Chrysler 9.25" Rear (Part No.32314)

Yukon Gear – Standard Open Carrier Case For ’09 & Down Chrysler 9.25" Rear (Part No.20008)

Yukon Gear – Positraction Clutch Guide (Part No.33352)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Yukon Gear – Differential Side Bearing Screw Adjuster For 9.25" Chrysler (Part No.33256)

Dorman – Differential Pinion Yoke Assembly (Part No.697-541)

Yukon Gear – Chrysler 8.75" "89" Housing Nodular Iron Drop Out Case (Part No.32052)

Richmond Gear – Differential Ring And Pinion (Part No.69-0145-1)

Yukon Gear – 8.25" Chrysler Notched Cross Pin (0.801" Diameter) (Part No.33433)

Yukon Gear – Standard Open Spider Gear Kit For 9.25" Chrysler With 31 Spline Axles (Part No.16004)

Motive Gear – Differential Gear Install Kit (Part No.C9.25IK)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Replacement Clutch Set For Dana 44 Powr Lok, Smooth (Part No.16152)

Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)

Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)

Yukon Gear – 9.25" Chrysler, Dana 60 Semi-Float X/P Bolt, 80 & Up, 5/16" Head, Tapered Shoulder (Part No.33238)

Yukon Gear – Pinion Depth Shim Kit For Toyota8", GM 7.5", 8.2" & 12 Bolt Truck (Part No.55064)

Yukon Gear – Dura Grip For Chrysler 9.25" Rear (Part No.26019)

Felpro – Differential Carrier Gasket (Part No.RDS 6583)

Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)

USA Standard Gear – Spartan Spring & Pin Kit, Fits Smaller Designs (Part No.17011)

Motive Gear – Differential Pinion Nut (Part No.1260823)

National – Multi Purpose Seal (Part No.7216)

Popular 1969 Dodge Monaco Differentials Categories

1969 Dodge Monaco Differentials

Differentials Brands To Make Your 1969 Dodge Monaco Last

Popular Dorman Differentials

Top 1969 Dodge Monaco Differentials from Driveworks

FAQs for 1969 Dodge Monaco Differentials

What are the most purchased Differentials for the 1969 Dodge Monaco?

What are the top-rated 1969 Dodge Monaco Differentials?

More Popular Parts for All Makes