1969 Chevrolet C10 Suburban Performance and Racing Products

Essential 1969 Chevrolet C10 Suburban Performance and Racing Products

Motive Gear – Differential Mini Spool (Part No.MS12C)

Differential Mini Spool

from

$108.99


Product Features:
  • MINI SPOOL GM12 BOLT CAR & TRUCK STRANGE # 088430
See More

Holley – Off Road Carbs (Part No.0-90670)

Off Road Carbs

from

$724.99
The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:
  • Gold Dichromate Finish For Extreme Off Road Environments
  • Single Feed Fuel Inlet For Ease Of Installation
  • Optimized Off-Road Calibration That Works Out-Of-The-Box
  • Factory Preset Electric Choke For Easy Startups
  • Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
  • One Piece Off-Road Vent Tube Eliminates Fuel Spillover
  • Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
  • Limited Lifetime Warranty Defects In Material/Workmanship
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Accel – Distributor Cap And Rotor Kit (Part No.8124)

Distributor Cap And Rotor Kit

from

$48.49


Product Features:
  • Heavy Duty Cap and Rotor Kit
  • With Brass Inserts
See More

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Mr. Gasket – Enhancement Products (Part No.2060)

Enhancement Products

from

$10.49
This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:
  • Internally battled
  • High-porosity filter
  • Ideal for high performance
  • Includes rubber grommet
See More

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Intake Manifold Bolts

from

$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:
  • Features 12-point Smaller-than-standard Bolt Head
  • Thick Flat Washers Distribute Optimum Clamp Load
  • Ideal Use Where Space Is Minimal On Race Manifolds
  • Bolts And Washers Zinc Plated For Protection
  • Zinc Plated For Protection
See More

Energy Suspension – Body Mount Set (Part No.3.4149R)

Body Mount Set

from

$213.99
Will replace distorted and worn-out original rubber mounts to maintain car body and truck cab to bed alignment. Original rubber mounts are so soft they often crack, distort, and crush so badly they often fall off and aluminum body mounts are too harsh for street use that they tend to break and cause other components to break. Energy’s specially formulated Hyper-Flex polyurethane cab and body mounts combine the best qualities of both: they’re soft enough for a smooth ride, yet rugged enough for the most demanding road or track. Most sets have a strong zinc plated steel ring molded into them – for added durability and when the application requires it.

Product Features:
  • Replace to Restore Ride Height
  • Gain Durability
  • Stronger Than Original Rubber Mounts
See More

Mr. Gasket – Chrome Plated Engine Oil Pan (Part No.9779)

Chrome Plated Engine Oil Pan

from

$153.99
Beautifully chrome plated. Complete with drain plug, washer & bolts (stock depth). Chrome-plated dipsticks with tubes sold separately.

Product Features:
  • Chrome plated
  • Includes drain plug/washer/bolts
See More

Accel – Custom Fit Spark Plug Wire Set (Part No.8843)

Custom Fit Spark Plug Wire Set

from

$112.99
These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:
  • 8.8mm Graphite Suppression
  • Silicone Spark Plug Boots
  • 550 Degree Double Silicone Construction
  • Fiberglass Braid
  • Carbon/Graphite Core
  • Magnetic Suppression
  • Fiberglass/Kevlar Core
  • 500 Ohms Resistance
See More

B & M – Flexplate, SFI 29.1 Approved, Fits 168-Tooth, 2-Piece Rear Main Seal, Chevy V8 (Part No.20230)

Flexplate, SFI 29.1 Approved, Fits 168-Tooth, 2-Piece Rear Main Seal, Chevy V8

from

$154.99
As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:
  • NHRA/IHRA Legal For All Classes
  • Includes SFI Certification Sticker
  • Ideal For Street Applications
  • To Extreme Duty Racing
  • To High RPM Use
See More

Edelbrock – VALVE COVERS (Part No.4280)

VALVE COVERS

from

$189.88
Product Features:
  • Polished Finish
  • Raised Fins w/Black Mat Background
  • Detailed With Allen Hex Heads
  • 2 Piece Look; 1 Piece Construction
  • Clears Most Roller Rockers
  • Clears Valvetrain Components
  • Heavy Gauge
See More

B & M – Shift Improver Kit For 65-87 TH400 Transmission (Part No.20260)

Shift Improver Kit For 65-87 TH400 Transmission

from

$62.99
The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:
  • Provides Crisp Shifts
  • On Any Stock Automatic Transmission
  • Eliminates Soft/Sluggish Shift
  • Eliminates Shift Overlap
  • Eliminate Clutch and Band Wear
  • Improves Transmission Life
  • Transmission Removal Not Required
See More

Competition Cams – Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set (Part No.7513-16)

Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set

from

$157.99
Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:
  • 3/8″ Diameter, 7.800″ Length
  • Magnum Pushrods for Small Block Chevy
  • One-piece .080″ wall chromemoly steel tubing
  • Heat-treated for extended durability and guide plate compatibility
  • Precision formed and reinforced pushrod end
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

Mr. Gasket – Alternator (Part No.5123)

Alternator

from

$363.99
These Mr. Gasket chrome alternators are remanufactured to exceed original equipment specifications for maximum dependability.

Product Features:
  • Fits Most 1966-’72 GM Vehicles
  • Bolt Spacing 6.6″
  • 80 Amps
  • GM 10DN Style Alternator
  • Chrome Plated Finish
  • includes V-Belt Pulley – 1-Groove
  • Use w/ OEM Style Regulator
See More

Mr. Gasket – Alternator Bracket (Part No.5171)

Alternator Bracket

from

$37.69
These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated for lasting beauty, Similar in design to OEM units, these brackets can be adapted to other engines.

Product Features:
  • Replaced GM # 6262956
  • Polished To High Luster
  • Chrome Plated For Lasting Beauty
See More

Edelbrock – Water Pump Big-Block Chevy Short/Standard in Black Finish (Part No.88503)

Water Pump Big-Block Chevy Short/Standard in Black Finish

from

$402.99
Edelbrock #88503 Water Pump big block Chevy short black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pu

Product Features:
  • Standard Impeller Rotation
  • 0.625 in. Pilot Shaft
  • 0.750 in. Ball/Ball Bearing
  • 5.750 in. Block To Hub Height
  • Black Finish
See More

MSD Ignition – Distributor Cap; Alkyd; MSD Chevy V8 Distributor (Part No.8437)

Distributor Cap; Alkyd; MSD Chevy V8 Distributor

from

$48.49
All MSD extra duty distributor caps are designed with performance in mind and are molded from high quality, voltage insulating material and use low resistance terminals.

Product Features:
  • Update The GM Points Cap w/MSD Performance
  • High Quality; Voltage Insulating Material
  • Low Resistance
  • Performance replacement part
See More

Weiand – Supercharger Remote Thermostat Housing (Part No.7134P)

Supercharger Remote Thermostat Housing

from

$184.99


Product Features:
  • Remote Thermostat Housing
See More

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

Spectre Replacement Air Filter

from

$31.99
This Spectre OEM replacement air filter is an easy to install performance option for multiple Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac applications that use a 14 inch by 3 inch round air filter. With its performance synthetic air filter media, this air filter has been designed to add horsepower and quicker acceleration by allowing more air flow into your engine than ordinary paper filters. This air filter’s sealing edge was engineered to insure a proper air cleaner housing seal for great engine protection.

Product Features:
  • Replacement for 14 inch by 3 inch round air filter
  • Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
  • Engineered for increased flow and greater performance
  • Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
  • Factory pre-oiled and ready to use
  • Simple installation
See More

MSD Ignition – Distributor; Chevy V8; Billet with Vacuum Advance (Part No.8361)

Distributor; Chevy V8; Billet with Vacuum Advance

from

$399.99
The street Pro-Billet is a popular route for people looking for proven race performance for their street cars. A vacuum advance canister provides economy and the proven MSD mechanical advance gives you the opportunity to dial-in a timing curve to fit your needs. Inside, an oversized steel shaft is QPQ coated for low friction and rides in a sealed ball bearing at the top of the distributor with an extra-long sintered bushing at the bottom. This combination keeps the shaft steady creating accurate spark delivery at any RPM. The street Pro-Billet relies on a magnetic pick-up to trigger the MSD Ignition control which delivers the powerful sparks to the coil. This pick-up is extremely accurate and never needs adjusting.

Product Features:
  • Designed for street/performance use w/mechanical or vacuum adv.
  • Must Be Used w/An MSD Ignition Control
  • Supplied w/An HEI Style Distributor Cap And Rotor
  • Accepts Cap-A-Dapts
  • O-ring seals can be installed for oil press. control (Mods only)
  • Special oil tract improves lubrication to the dist./cam gear
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
See More

Mr. Gasket – Dust Cap (Part No.2485)

Dust Cap

from

$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:
  • Chrome Plated Steel
  • Set of 2 Caps
  • Easy Installation
  • 2 Per Set
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5908)

Ultra Seal: Exhaust Gasket Set

from

$45.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Manufactured from high-temperature steel core/graphite faced exhaust material.
  • Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
  • Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
  • Conforms to and seals minor surface irregularities
  • Can be trimmed if necessary for modified port applications
  • For OE replacement, high performance street, drag race and oval track use
  • Anti-Stick Properties
  • Easy Removal For Disassembly
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.182)

Valve Cover Gasket Set

from

$42.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance.brbrFits Chevrolet 396,402,427,454,502 Gen IV, Gen V and Gen VI Big Block.

Product Features:
  • This Gasket Has A Cork Rubber Blend
  • Provides Excellent Sealing And Durability
  • Extra Thick For The Hard To Seal Applications
See More

Spectre – Aluminum Timing Pointer (Part No.4936)

Aluminum Timing Pointer

from

$64.99
Spectre’s timing tabs have an adjustable timing pointer to allow for a more accurate reading and they can work with any size harmonic balancer. Designed for Chevy small block engines, Spectre’s adjustable timing tabs have a polished aluminum finish so it will look great under your hood.

Product Features:
  • Polished aluminum finish
  • Designed for Chevy small block engines
  • Adjustable pointer allows for use with 6, 7, and 8 In. harmonic balancers
  • Installs easily where original tab mounts
See More

Fram – High Performance Spin-on Oil Filter: Ideal for Racing Oil (Part No.HP4)

High Performance Spin-on Oil Filter: Ideal for Racing Oil

from

$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.** 

Product Features:
  • Proven protection for up to 10,000 miles
  • Engineered for use with synthetic or conventional motor oils
  • Filter media is a blend of fiber and resin that captures 95% of the dirt particles
  • The perfect balance of dirt-trapping efficiency and dirt-holding capacity
See More

Mallory – Distributor Condenser (Part No.401)

Distributor Condenser

from

$17.09
Distributor Condenser

Popular 1969 Chevrolet C10 Suburban Performance and Racing Products Categories

1969 Chevrolet C10 Suburban Performance and Racing Products

You count on your 1969 Chevrolet C10 Suburban to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 266 Performance and Racing Products ranging in price from $7.99 to $1,009.99, you’re sure to find everything you need for your 1969 Chevrolet C10 Suburban.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 20 different brands like Mr. Gasket, Edelbrock, and K&N. 1969 Chevrolet C10 Suburban Performance and Racing Products start as low as $7.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 1,363 extensive product reviews on 1969 Chevrolet C10 Suburban Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Ultra-Seal Intake Manifold Gasket with Silicone Beading with 4.3 stars and Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration with 4.9 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1969 Chevrolet C10 Suburban below to get started!

Top-Rated Performance and Racing Products Brands For Your 1969 Chevrolet C10 Suburban

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1969 Chevrolet C10 Suburban running right for years to come. In our inventory you’ll find brands like Mr. Gasket, Edelbrock, K&N, and even more.

Popular Flowtech Performance and Racing Products

You’ll find popular Flowtech brand products across Performance Exhaust Products. All are waiting to get your 1969 Chevrolet C10 Suburban back on the road. Some of the top-rated Flowtech products in these categories are:
Real-Seal; Header Gasket
from $85.39
(1)
Real-Seal; Header Gasket
Performance Exhaust Manifold Gaskets

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1969 Chevrolet C10 Suburban, and some of our most reviewed Edelbrock parts include:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds

FAQs for 1969 Chevrolet C10 Suburban Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1969 Chevrolet C10 Suburban?

Out of 266 Performance and Racing Products for the 1969 Chevrolet C10 Suburban, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

What are the top-rated 1969 Chevrolet C10 Suburban Performance and Racing Products?

Top-rated Performance and Racing Products for your 1969 Chevrolet C10 Suburban based on customer reviews/ratings are:
Ultra-Seal Intake Manifold Gasket with Silicone Beading
from $31.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
“Can’t go wrong with Mr Gasket”
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
from $89.99
(14)
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
“I just installed a new crate 350 in my 1956 Bel Air. I’ve used K&N’s before and I’m looking forward to improved performance and long use with this fi”
Performance Exhaust Gasket Set for Enhanced Sealing and Durability
from $20.99
(14)
Performance Exhaust Gasket Set for Enhanced Sealing and Durability
“Put new headers on motor”