from

$264.99

Product Features:

Fits Ford 9″ with 28 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
Races installed
6061 aluminum
Annodized purple

from

$11.99

Side gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

Side gear thrust washer for Ford 8.8″
0.875″ diameter cross pin shaft applications only

from

$74.99

1.250″ pinion adaptor sleeve (stock pinion into large support).

Product Features:

Adapter sleeve
Fits Ford 9″
Adapts 28 spline pinion into 35 spline pinion support

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$289.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

Fits 2009 and down Ford 8.8″
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

from

$993.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 31 spline axles and loadbolt housing
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$315.99

Yukon positraction internals for 8″ and 9″ Ford with 31 spline axles, in a 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 9″ with Trac Loc positraction with 31 spline axles
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$119.99

8.8″ FORD 09 & DWN PINION KIT .

Product Features:

Fits 2009 and down Ford 8.8″
Uses Koyo bearings and races
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, marking compound and brush.

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$264.99

TracLoc clutch set (two sides) for 7.5″ Ford.

Product Features:

Clutch kit
Fit Ford 7.5″ Trac Loc positraction

from

$3.99

Adjuster lock bolt 3.062″ & 3.250″ Yukon Ford 9″ Drop Out.

Product Features:

Side adjuster lock bolt

from

$57.99

8.8″ Ford 7/8″ diameter Notched cross pin shaft (.875″ for ’86 and newer). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Notched cross pin shaft for Ford 8.8″
0.875″ diameter
Not compatible with Spartan Locker or Powertrax Lock Right

from

$483.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
18 piece kit
Steel clutches

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$63.99

Product Features:

Trac Loc spring
Fits 28 spline Ford 8.8

from

$5.99

Fine thread pinion support bolt (aftermarket aluminum only) for 9″ Ford.

Product Features:

Pinion support bolt for Ford 9″
3/8″ x 24 thread
1.5″ long

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$31.99

Product Features:

MINI SPOOL 8″ & 9″ 31 SPLN STL 090431

from

$20.49

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.

Product Features:

.047″ thick cellulose/nitrile composite gasket material
Precision die cut
Reusable

from

$135.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$184.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 7.5″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$409.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Ford 9″
9.00″ ring gear diameter
28 spline pinion
10 ring gear bolts
5.29 ratio

from

$0.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$153.99

M802048 set-up bearing (one bearing). No return.

Product Features:

Set up bearing
Fits M802048 pinion bearing
Easily slips on and off pinion journal to allow for easier pinion depth adjustment

from

$12.79

Product Features:

High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks
Long-life friction modifiers and premium base oils help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
Enhanced cleaning additives help reduce varnish formation and keep the transmission running properly longer
Engineered with a unique blend of viscosity modifiers and base oils to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$51.99

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

Carrier race
Fits Ford 9″
Conversion race to install small bearing carrier into 3.250″ dropout

from

$442.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!