from

$16.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$80.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$636.99

Product Features:

Square Flange Carburetor Mounting
Special D-Shaped Port Runner Design
Large Plenum Chamber

from

$438.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking

from

$185.99

RngPnn

from

$165.99

Available in different sizes for many different vehicle models/years. Clean positive seal. Embossed silicone bead surrounding the port. Matched to manifolds and cylinder heads. In the early days of the automotive performance industry, you either ran what

Product Features:

Clean positive seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads
Fits 1963-96 289/302/351W Engines
10-Pack Of Gaskets

from

$64.99

Replace your stock black engine pulleys with chrome plated steel pulleys from Mr. Gasket.

Product Features:

Triple Groove
Chrome Plated
Diameter: 5.90″

from

$499.99

The industry standard for over 30 years, this shifter offers state of the art transmission control for popular manual transmissions. Dedicated applications assure a custom fit to a wide variety of vehicles.

Product Features:

High Ratio Pivot Mechanism
Adjustable Bias Spring Loads
Adjustable Stops
Chrome Plated Steel Bolt On Stick
Easy Installation

from

$190.99

Edelbrock part #9659 Pushrods are designed for small-block Ford 351W V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precise f

Product Features:

7.7 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$18.99

Oil Pan Bolt Kit

from

$126.99

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a rich powerful tone and are the most aggressive, highest performing street muffler we’ve ever built in a four inch case. Constructed of 16 gauge 409S stainless steel and fully MIG welded for maximum durability.

from

$166.99

A true performance application component for cars, trucks, hot rods, racing/competition, yet popularly used for street vehicles when more horsepower is added. Soft running enough to absorb vibrations for street use yet rugged for racing use. Helps control torque on high performance vehicles. Maintains proper drive shaft angle to help prevent early wear and unexpected power train damage. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal transmission mounts. Resistant to under vehicle fluid oils, coolants and road contaminants. Made of Energy’s Hyper-Flex performance polyurethane and heavy duty hardware – for added durability.

Product Features:

Unique Safety Interlock Design
Impervious to Vehicle Oils and Chemicals
Strong Enough Too Handle High Performance

from

$109.99

Product Features:

Made from HYPER-Flex Polyurethane

from

$226.99

Product Features:

FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES

from

$315.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$153.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for Ford, Lincoln and Mercury (externally balanced) 289 and 302ci V8 engines with 28.2 ounce imbalance. Features include high tensile strength steel to resist elongation and cracking, 10.50 inch bolt pattern and 157 tooth ring gear. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M flexplates are ideal for hot rods, street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with C4 and C6 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$37.49

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Withstands Intense Exhaust Heat
Graphite-Impregnated Facing
Steel Expanded Metal Core
Superior Tensile Strength
Resists Deteriorating
Anti-stick Properties
Easy Removal For Disassembly

from

$28.99

Available in kits including front cover gasket, crankshaft seal, fuel pump and water pump gasket or including cover gasket and front seal.

Product Features:

Timing Cover Gasket And Oil Seal Kit

from

$237.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$13.29

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed. Fits 1962-2001 Small Block Ford V8s, including both Windsor and Cleveland as well as Ford 385 series 429/460 big blocks including Boss models.

Product Features:

Eliminates bolt in favor of stud mount design
Chrome plated
Ideal For Ignition Distributor

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$200.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 130+ gph Free Flow
Shutoff Pressure Pre-Set From 7.5 To 9 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Always Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$72.99

Shift Improver Kit – 1970 to 1982 Ford, Lincoln, Mercury C4 Application: 1970 to 1982 Ford, Lincoln, Mercury C4 Recalibrate your automatic transmission for optimum performance and extended life! Select the mode that best suits your application Provides crisp shifts on any stock automatic transmission Eliminates shift overlap and excess wear on clutches and bands due to slippage The B&M Shift Improver Kit the easiest way to get the stout performance you’ve always wanted out of your automatic transmission – and you get two modes of performance to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit. All you need are some hand tools! In the space of an afternoon, you can turn your transmission into a B&M-tuned unit! Ask the thousands of satisfied customers that have installed one in their transmissions! STAGE 1. HEAVY DUTY Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. Recommended for regular passenger vehicles. STAGE 2. STREET/STRIP Provides positive shifts for high performance street use or for competitive events. This level is for the enthusiast who wants the hardest, quickest possible shift.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$569.99

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky duration systems or ancient breaker point models. These distributors come complete and Ready-to-Run. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs.

Product Features:

Now includes built-in Rev Limiter
Built-in module produces a 7.5 amp single spark through high rpm
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Housing Is 5/8 in. Smaller In Diameter Than Stock Ford Distr.
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
Polished steel shaft is guided by a sealed ball bearing
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
Mech. advance assem. can be locked out for crank trigger systems

from

$91.99

Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features: