1968 Dodge D200 Pickup Differentials

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard Limited warranty against defects on their ring & pinion sets.

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 35 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• DANA-60 R/P 4.10 STD MG (USES PRE-LOAD SHIMS)

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon 4340 Chrome-Moly replacement inner axle for Dana 60 with a length of 16.17″ and 35 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer for Chrysler 9.25″ rear

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Easily slips on and off pinion journal to allow for easier pinion depth adjustment
• Fits M802048 pinion bearing
• For popular GM, Ford, Dana, and Chrysler differentials

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights

Product Features:

• Brand may vary by location

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side adjuster for Chrysler 9.25″ rear

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. You can count on Yukon to fulfill all your differential small parts needs.

Product Features:

• Clutch kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Power Lok positraction
• Smooth design

Yukon Minimum Installation Kits are a low-cost solution for ring and pinion gear changes in newer vehicles where the bearings can be reused. Kits include all high-quality components for a smooth differential set up.

Product Features:

• Fits Chrysler 9.25″ rear
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Yukon spider gear set for GM 8.2″ Dura Grip posi, 28 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver select ability.

Product Features:

• Switch

8.75″ Chrysler gasket.

Product Features:

• Dropout gasket
• Fits Chrysler 8.75″

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits M88010 race
• For accurate installation of bearing races
• All-steel construction

Yukon Bearing Installation Kits are perfect for shops and builders who have shims on the shelf and are looking to save cost over a Master Overhaul Kit. This kit uses Timken bearings and races along with all high-quality small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to properly install your ring and pinion gear set.

Product Features:

• Fits 1975 and down Chrysler 8.25″
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Cross pin shaft
• Fits Chrysler 9.25″
• Standard open carrier only
• Notched

Union 76 gear oil is a conventional non-synthetic 80W90 formulation designed for all types of differentials.

Product Features:

• Includes three quarts of conventional oil

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut
• Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard Limited warranty against defects on their ring & pinion sets.

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 30 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Inner oil slinger for Dana Spicer 60

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits Dana Spicer 60 and 70
• 29 spline
• 1310 u-joint size
• Outside snap ring design
• 3.219″ snap ring span
• 1.062″ cap diameter
• Strap style

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits Dana Spicer 60, 70, 70U and 70HD
• 29 spline
• 7290 u-joint size
• 2.625″ snap ring span
• 1.125″ cap diameter
• Inside snap ring design
• Strap style