1966 Ford Falcon Differentials

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 2.891″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Ford 9″ with LM102910 carrier race
• Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

8″ Ford O-ring.

Product Features:

• Pinion support o-ring
• Fits Ford 8″

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

Product Features:

• Spider gear kit
• Fits Ford 8″ and 9″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with oversize Daytona pinion support
• 28 spline
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Product Features:

• Friction plate
• Fits Ford 8″ and 9″ Trac Loc positraction

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Worn or damaged differential end yoke causing driveline Vibrations! This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

• Pilot bearing
• Fits Ford 9″
• 0.656″ thick

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. This unit uses the factory side gears.

Product Features:

• Fits Ford 8″ and 9″ with 28 or 31 spline axles
• Made from 9310 steel for added strength
• Works with stock side gears in standard carrier case

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

• Pilot bearing
• Fits Ford 8″

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered and manufactured specifically for the repair environment
• Unsurpassed quality you can trust
• Includes all parts needed to complete the repair

Product Features:

• Pinion depth shim kit
• Fits Ford 9″ with 7/16″ pinion support bolts

Product Features:

• Fits Ford 9″ with 28 spline pinion
• Larger inner pinion bearing reduces gear deflection under high load
• Races installed
• Nodular iron

Adjuster lock bolt 3.062″ & 3.250″ Yukon Ford 9″ Drop Out.

Product Features:

• Side adjuster lock bolt

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

9″ Ford 2 piece solid preload pinion spacer, Daytona or standard.

Product Features:

• Crush sleeve eliminator kit for Ford 9″ with 28 spline pinion

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Trac Loc positraction
• Clutch style positraction
• Street design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

8″ Ford pilot bearing retainer.

Product Features:

• Pilot bearing retainer for Ford 8″

Product Features:

• Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
• 0.030″ thick

Standard open cross pin shaft (.750″) for Ford 8″, 8.8″, 9″ and Model 20.

Product Features:

• Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
• Fits standard open differentials only
• 0.750″ diameter

1.250″ pinion adaptor sleeve (stock pinion into large support).

Product Features:

• Adapter sleeve
• Fits Ford 9″
• Adapts 28 spline pinion into 35 spline pinion support

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 8″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Ford 8″
• 8.00″ ring gear diameter
• 25 spline pinion
• 10 ring gear bolts
• 3.55 ratio

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For use with Trac Loc limited slip
• 1.25″ long