1966 Dodge D100 Series Performance and Racing Products

Essential 1966 Dodge D100 Series Performance and Racing Products

Spectre – Water Neck; Chrysler (Part No.4739)

Water Neck; Chrysler

from

$23.79
Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:
  • Fits 1964 and later Chrysler V8 engines
  • Includes bolts
  • Chrome plated
  • Easy to install
  • O-ring/gasket not included
See More

Accel – Ignition/Electrical (Part No.2030)

Ignition/Electrical

from

$79.99
Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • More Accurate Ignition Timing
  • Improves Performance
  • Provides More Accurate Ignition Timing
  • Easy To Install w/Hand Tools
  • Reduced Maintenance
  • Thermal Clad Based Surface Mount Construction
  • Utilizes Specialized Electronic Circuitry
  • Ignition Timing Is Stable From 1 To 10000rpm
See More

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Intake Manifold Bolts

from

$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:
  • Features 12-point Smaller-than-standard Bolt Head
  • Thick Flat Washers Distribute Optimum Clamp Load
  • Ideal Use Where Space Is Minimal On Race Manifolds
  • Bolts And Washers Zinc Plated For Protection
  • Zinc Plated For Protection
See More

Mr. Gasket – High Performance Thermostat (Part No.4366)

High Performance Thermostat

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens at 160 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Stainless Steel, Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Spectre – Valve Cover (Part No.5277)

Valve Cover

from

$72.99
Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1979 Chrysler Big Block 361-383-400-413-426-440 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:
  • Designed for 1958-1979 Chrysler Big Block 361-383-400-413-426-440 engines
  • Baffled for breather system compatibility
  • Sold in pairs
  • Triple chrome-plated steel construction
  • Stock height
  • Features OEM style sealing edge
See More

Mr. Gasket – Breather/Oil Filler Cap (Part No.2059)

Breather/Oil Filler Cap

from

$14.29
Chrome plated breather cap is ideal for race car vacuum balance systems, as well as original equipment applications with positive crankcase ventilation (PCV).

Product Features:
  • Features 1″ O.D. neck and a 5/8″ O.D. breather tube
  • Breather has Metal/Foam Baffle inside and includes Grommet
  • Fits all aftermarket valve covers with a 1.22″ Dia. opening
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1008)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

VALVE SEALS, TEFLON 3/8" 1 ST

from

$31.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:
  • Work with .530″ guides and 3/8″ valve stem diameter
  • Valve stem oil seals keep unwanted oil from entering the combustion chamber
  • Several different types of valve seals are offered
See More

Rancho – Steering Damper Bracket (Part No.RS5508)

Steering Damper Bracket

from

$80.99
Rancho® high-performance steering stabilizers are a simple and affordable way to enhance a vehicle’s performance. Rancho® steering stabilizers are ideal for off – road driving, towing/hauling and street performance applications. Rancho® steering stabilize

Product Features:
  • Black powder coated for visual appeal
  • CNC cut or bent
  • Steel thickness
  • Direct bolt to factory steering linkage
  • Designed for dual steering stabilizer
See More

K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1540)

Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration

from

$149.99
K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:
  • ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
  • RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
  • 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
  • CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
  • ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
  • EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
  • ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
  • MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability
See More

MSD Ignition – Wire Set; Super Conductor; Chrysler 383-440 HEI for MSD Distributor (Part No.32739)

Wire Set; Super Conductor; Chrysler 383-440 HEI for MSD Distributor

from

$175.99
The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:
  • Bolt-on Performance
  • Custom Fit For Make And Model Listed
  • Wires Are Pre-Cut To Exact Specifications
  • Conductor core features DuPont Kevlar material for increased tensile strength
  • Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
  • Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately
See More

Mr. Gasket – Oil Pan Bolt Kit (Part No.6088)

Oil Pan Bolt Kit

from

$18.99
Oil Pan Bolt Kit

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 8 Piece Set (Part No.1214)

Lower Intake Manifold Gasket Set: 8 Piece Set

from

$46.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

Mr. Gasket – Dust Cap (Part No.2485)

Dust Cap

from

$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:
  • Chrome Plated Steel
  • Set of 2 Caps
  • Easy Installation
  • 2 Per Set
See More

Edelbrock – Performer RPM Series fuel pump is for Small-Block Chrysler (Part No.1720)

Performer RPM Series fuel pump is for Small-Block Chrysler

from

$209.99
Edelbrock part #1720 Performer RPM Series fuel pump is for Small-Block Chrysler designed for use with all Edelbrock carburetors used in Performer or Performer RPM applications. These high-performance’s street Fuel Pumps feature a high quality three stage
See More

Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)

Super Stock Replacement Coil for Improved Performance, Starting, and Power

from

$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:
  • 42000 Volts
  • Effective To 6500 RPM
  • Quicker Starting
  • Improved Throttle Response
  • Higher RPM Power
  • Can Finished In Yellow
See More

Earls Performance Product – Solo Bleed (Part No.280021ERL)

Solo Bleed

from

$32.59


Product Features:
  • Prevents Air Inclusion
  • Direct Replacement
  • For OE Bleeders
  • One Person Bleeds Safely
  • Without The Mess
  • No Chance Of Air Bubbles
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1413)

Exhaust Manifold Gasket Set

from

$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

B & M – Flexplate, 6 Bolt Crank for TF 727 (Part No.10230)

Flexplate, 6 Bolt Crank for TF 727

from

$154.99
As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:
  • NHRA/IHRA Legal For All Classes
  • Includes SFI Certification Sticker
  • Ideal For Street Applications
  • To Extreme Duty Racing
  • To High RPM Use
See More

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Remote Oil Filter Kit

from

$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:
  • Relocate oil filter to an easy access location
See More

Hurst – B-1 Shifter Boot and Plate (Part No.1147336)

B-1 Shifter Boot and Plate

from

$42.49
Designed for use with round stick shifters. Complete with chrome ID plate and mounting hardware. Measures: 4-3/8 in. x 5-3/8 in. with 3 pleats.

Product Features:
  • Complete with Mounting Hardware
  • Adapt To Most Shifter Install
  • Hurst Quality
  • Works Well with Round Shift Levers
  • Chrome ID Plate
See More

Richmond Gear – RngPnn (Part No.69-0375-1)

RngPnn

from

$342.99
RngPnn

Competition Cams – High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for Chrysler 273-360 (Part No.CL20-212-2)

High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for Chrysler 273-360

from

$1093.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:
  • Good blend of efficiency and performance.
  • Perfect choice for performance street rebuilds.
  • Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
See More

Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)

Super Intake Manifold Bolts

from

$27.49
These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:
  • Assures Accurate Torque App
  • Prevents Galling Manifold
  • Grade 5 Material
  • Black Oxide Coasted
See More

Edelbrock – RPM Air-Gap Small Block Chrysler Black Intake Manifold (Part No.75763)

RPM Air-Gap Small Block Chrysler Black Intake Manifold

from

$612.99
Edelbrock part #75763 RPM Air-Gap intake manifold is designed for 340-360 c.i.d. Chrysler V8’s and 318 c.i.d. engines with 340-360 cylinder heads. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competit

Product Features:
  • 1500-6500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 4.9 in. Front Height, 5.35 in. Center Height, 5.8 in. Rear Height
  • Black Powder Coated Finish
  • Made In The USA
See More

Competition Cams – VALVE SPRINGS, 1.509" DUAL 1 ST (Part No.924-16)

VALVE SPRINGS, 1.509" DUAL 1 ST

from

$788.99
Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:
  • Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
  • O.D.: 1.509″, I.D.: 0.697″
  • Dual valve springs with damper
See More

Competition Cams – Engine Valve Spring Kit (Part No.911-16)

Engine Valve Spring Kit

from

$759.99
Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

Product Features:
  • Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
  • O.D.: 1.524″, I.D.: 1.110″
  • Single valve springs with damper
See More

1966 Dodge D100 Series Performance and Racing Products

You count on your 1966 Dodge D100 Series to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 47 Performance and Racing Products ranging in price from $12.09 to $1,093.99, you’re sure to find everything you need for your 1966 Dodge D100 Series.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 16 different brands like Accel, Mr. Gasket, and Fram. 1966 Dodge D100 Series Performance and Racing Products start as low as $12.09!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 178 extensive product reviews on 1966 Dodge D100 Series Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration with 5.0 stars and Intake Manifold Bolts with 4.6 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1966 Dodge D100 Series below to get started!

Top-Rated Performance and Racing Products Brands For Your 1966 Dodge D100 Series

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1966 Dodge D100 Series running right for years to come. In our inventory you’ll find brands like Accel, Mr. Gasket, Fram, and even more.

Popular Competition Cams Performance and Racing Products

You’ll find popular Competition Cams brand products across Performance Engines. All are waiting to get your 1966 Dodge D100 Series back on the road. Some of the top-rated Competition Cams products in these categories are:
VALVE SEALS, TEFLON 3/8" 1 ST
from $31.99
(1)
VALVE SEALS, TEFLON 3/8" 1 ST
Performance Engine Valve Stem Seal Sets

FAQs for 1966 Dodge D100 Series Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1966 Dodge D100 Series?

Out of 47 Performance and Racing Products for the 1966 Dodge D100 Series, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
High Performance Thermostat
from $27.49
This product is not rated
High Performance Thermostat
Performance Engine Coolant Thermostats
High Perf. Full-Flow Lube Spin-on
from $16.99
(4)
High Perf. Full-Flow Lube Spin-on
Performance Oil Filters

What are the top-rated 1966 Dodge D100 Series Performance and Racing Products?

Top-rated Performance and Racing Products for your 1966 Dodge D100 Series based on customer reviews/ratings are:
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
from $102.99
(5)
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
“Seeing the commercials on the speed channel got me thinking about my 1996 Dodge Dakota 4×4 with V-6, with a lot of miles. Needed a boost of power and”
Intake Manifold Bolts
from $32.09
(5)
Intake Manifold Bolts
“Excellent product.”
Unilite Ignition Module
from $85.29
(3)
Unilite Ignition Module
“I like the Unilite product because it is so small and compact compared to the HEI stuff I normally use. If you are restricted on space Its a great pro”