1965 Oldsmobile Jetstar I Performance and Racing Products
More 1965 Oldsmobile Jetstar I Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1965 Oldsmobile Jetstar I, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1965 Oldsmobile Jetstar I Performance and Racing Products
Energy Suspension – Tie Rod Dust Boot (Part No.9.13101G)
from
$9.99
Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.
Product Features:
See More
Product Features:
- Easy to Install
- Superior Material
- Saves Your Tie Rods
- Lasts Longer
- Looks Great
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$27.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Edelbrock – Performer Intake Manifold for Olds 400-455, Non-EGR, Satin (Part No.2151)
from
$494.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Energy Suspension – Control Arm Bushing Set (Part No.3.3132R)
from
$154.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Mr. Gasket – Oil Pan Bolt Kit (Part No.6085)
from
$17.49
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.
Product Features:
See More
Product Features:
- Ideal For Tight Spaces
- Serrations Prevent Loosening
- Flange Distributes Pressure
- Zinc Plated Bolts
- Grade 5 Material
- Easy Installation
Edelbrock – Intake Manifold Gasket for 1965-76 400-425-455 Oldsmobile engines (Part No.7284)
from
$28.99
Product Features:
See More
- 1.44″x2.44″
- Features Embossed Silicone Bead Around The Intake Ports & Water Openings
- .060″ Thick
- Two Piece Configuration
- End Seals Not Included
Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7813)
from
$97.99Product Features:
- Solid Bushing Chain Resists Stretching
- For Use with Stock or Edelbrock Camshafts
- Stressproof Steel Crank Gears
- 3 Keyway Setting Points To Ensure Accurate Timing
- True Bearing Surface Rolls with the Sprockets
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1439)
from
$30.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Energy Suspension – Sway Bar End Link Kit (Part No.9.8118G)
from
$26.99
Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.
Product Features:
See More
Product Features:
- Made from HYPER-Flex Polyurethane
- Allows Vehicle to Work At Maximum Efficiency
- Easy to Install
- Superior Performance and Greater Longevity
- Lasts Much Longer Than OEM Rubber End Links
Energy Suspension – Control Arm Bushing Set (Part No.3.3132G)
from
$154.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Accel – Distributor Cap And Rotor Kit (Part No.8124)
Richmond Gear – RngPnn (Part No.69-0033-1)
from
$315.99
RngPnn
Richmond Gear – MiniSpool (Part No.78-1230-1)
from
$151.99
MiniSpool
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2003)
from
$22.29
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
Edelbrock – Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9913)
from
$427.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Electric Choke Type
- 750 cfm Maximum Flow Rating
Mr. Gasket – EngFullGsktSet (Part No.7140)
from
$80.29
Kits include all gaskets needed for a complete engine overhaul. Cylinder head, intake, exhaust, valve cover and oil pan. Distributor gasket (where applicable), timing cover, fuel pump, thermostat, water pump, and rear main seal. For OE replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Engine Rebuilder
- Stock/Non-High Performance Engines
- Includes All Gaskets/Seals
Hays – Power Train (Part No.85-114)
from
$653.99
High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.
Product Features:
See More
Product Features:
- Built As Matched Assembly
- Exceptional Performance
- Exceptional Durability
- Long Term Dependability
Hays – Power Train (Part No.85-113)
from
$641.99
Power Train
B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)
from
$766.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 2800-3200 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
B & M – Torque Converter, Nitrous Holeshot 3600 (Part No.20482)
from
$665.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.
Product Features:
See More
Product Features:
- 3400-3800 RPM
- Small And Big Blocks
- Serious Performance
- Furnace Brazed
- Fully Balanced
Accel – Points Eliminator Kit (Part No.2010)
from
$105.99
Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- More Accurate Ignition Timing
- Improves Performance And Fuel Economy
- Provides More Accurate Ignition Timing
- Easy To Install w/Hand Tools
- Reduced Maintenance
- Thermal Clad Based Surface Mount Construction
- Utilizes Specialized Electronic Circuitry
- Ignition Timing Is Stable From 1 To 10000rpm
Accel – Contact Set Hp 32 Oz (Part No.110128)
from
$54.39
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.
Product Features:
See More
Product Features:
- Extra Thick Contact Arms
- Large Radius Tungsten Contacts
- High Strength Phenolic Rubbing Blocks
- Prevents Points Float
- Moisture-Proof Buna-N Condenser
Mallory – Distributor Condenser (Part No.401)
from
$17.09
Distributor Condenser
Spectre – Water Neck; Olds (Part No.4733)
from
$26.99
Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.
Product Features:
See More
Product Features:
- Fits Oldsmobile 330, 350, 425 and 455 engines
- Chrome plated
- Bolts included
- Designed for OEM fit
- Easy to install
- O-ring/gasket not included
Popular 1965 Oldsmobile Jetstar I Performance and Racing Products Categories
1965 Oldsmobile Jetstar I Performance and Racing Products
You count on your 1965 Oldsmobile Jetstar I to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 53 Performance and Racing Products ranging in price from $5.99 to $766.99, you’re sure to find everything you need for your 1965 Oldsmobile Jetstar I.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 13 different brands like Accel, Mr. Gasket, and Edelbrock. 1965 Oldsmobile Jetstar I Performance and Racing Products start as low as $5.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 161 extensive product reviews on 1965 Oldsmobile Jetstar I Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Mallory Kit: Unil Conv: Delco: V8 with 5.0 stars and Performer Intake Manifold for Olds 400-455, Non-EGR, Satin with 5.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1965 Oldsmobile Jetstar I below to get started!
Top-Rated Performance and Racing Products Brands For Your 1965 Oldsmobile Jetstar I
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1965 Oldsmobile Jetstar I running right for years to come. In our inventory you’ll find brands like Accel, Mr. Gasket, Edelbrock, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Oil Filters. All are waiting to get your 1965 Oldsmobile Jetstar I back on the road. Some of the top-rated K&N products in these categories are:
from
$22.29
(9)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
Top-Rated Edelbrock Performance and Racing Products
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1965 Oldsmobile Jetstar I, and some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Performance Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Performance Carburetors
from
$397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
Performance Carburetors
FAQs for 1965 Oldsmobile Jetstar I Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1965 Oldsmobile Jetstar I?
Out of 53 Performance and Racing Products for the 1965 Oldsmobile Jetstar I, the most popular in our inventory are:
from
$42.49
(54)
Super Stock Replacement Coil for Improved Performance, Starting, and Power
Performance Coils
from
$26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
What are the top-rated 1965 Oldsmobile Jetstar I Performance and Racing Products?
Top-rated Performance and Racing Products for your 1965 Oldsmobile Jetstar I based on customer reviews/ratings are:
from
$134.99
(1)
Mallory Kit: Unil Conv: Delco: V8
“I had my 66 LeMans 326 engine rebuilt. After the install, which was easy to do, and following the instructions the engine fired right up. Now I won’t ”
from
$494.99
(1)
Performer Intake Manifold for Olds 400-455, Non-EGR, Satin
“Replaced Edelbrock O4B with this intake. Immediately noticed the car had more power and ran better. One piece of advice, use the exhaust block off p”
