1965 Oldsmobile Jetstar 88 Performance Engines

Product Features:

• Best for the Ultimate in Street High-Performance
• Designed for Idle to 5500 RPM Street-Driven Power
• Dual-Plane High-Rise Intake w/180 deg Firing Order
• Produces Incredible Top-End Horsepower
• Retains Good Throttle Response and Acceleration
• Larger Plenum and Runners Maximizes Other Upgrades
• Edelbrock Total Power Package Maximizes Gains

Spectre’s Oldsmobile V8 water neck fits Oldsmobile 330, 350, 425 and 455 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck has an additional by-pass hose connection and includes the bolts.

Product Features:

• Fits Oldsmobile 330, 350, 425 and 455 engines
• Chrome plated
• Bolts included
• Designed for OEM fit
• Easy to install
• O-ring/gasket not included

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

• 2 in. adjustable range
• Includes necessary hardware
• Chrome plated
• Individually packaged

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 3400-3800 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Torque Converter – Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

• 2800-3200 RPM
• Small And Big Blocks
• Serious Performance
• Furnace Brazed
• Fully Balanced