from

$82.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for stock points or electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Supplied w/2 Spark Plug Wire Boots/Terminals/Ballast Resistor
100:1 Turns Ratio
Lower Primary Resistance Produces High Voltage Output
Metal Canister Is Filled w/Premium Grade Oil For Cooling
CARB E.O. Approved

from

$119.99

Spark Plug Wire

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$51.99

304 stainless steel mesh. 5 layer construction. Most durable filters in the industry. Outperforms the others in clean air testing. Assures cleanest air possible from washable filter. Provides balance between air flow and peak filtration. Lifetime no hassle warranty.

Product Features:

Multi-Layer Construction
Most Durable Filters In The Industry
Outperforms The Others In Clean Air Testing
Assures Cleanest Air Possible From Washable Filter
Washable And Reusable
Made In The USA
Lifetime No Hassle Warranty

from

$512.99

The industry standard for over 30 years, this shifter offers state of the art transmission control for popular manual transmissions. Dedicated applications assure a custom fit to a wide variety of vehicles.

Product Features:

High Ratio Pivot Mechanism
Adjustable Bias Spring Loads
Adjustable Stops
Chrome Plated Steel Bolt On Stick
Easy Installation

from

$397.99

Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.

from

$16.99

Cap off your radiator with a gleaming chrome plated filler cap. Made to last.

Product Features:

Chrome radiator caps
Made to last
Skin packaged

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$81.99

Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:

High Performance Points and Condenser
With Integral Conductor

from

$40.99

Product Features:

Valve Cover Gasket

from

$49.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$72.99

Product Features:

Non-Rotator Type
1.458 in. Outer Diameter
1.062 in. Inner Diameter
1.062 in. Coil Blind
Set of 16

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$144.99

Spectre’s Oil Pan was designed for Ford 260-302 engines requiring front sump application. This stock 4 quart capacity pan features a triple chrome-plated finish and durable steel construction. Precision engineered for optimum fit and function, this high quality OEM replacement part is easy to install.

Product Features:

Triple chrome-plated steel
For Ford 260-302 engines requiring front sump application
Stock 4 quart capacity
Easy to install with no special tools or skills required
Stock capacity

from

$766.99

Product Features:

Designed For Carbureted V8s
Power Increases From 100-250 HP
Precision EDM Machined Spray Bars
Simple To Install

from

$26.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$113.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$547.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$661.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
Accepts Late-Model Choke; Waterneck; and HEI
Accepts A/C And Alternator
Accepts Exhaust Heated Chokes

from

$72.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for Ford 429-460 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for Ford 429-460 engines
Baffled for breather system compatibility
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$72.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1976 Ford “FE” 332-352-360-390-406-410-427-428 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1958-1976 Ford “FE” 332-352-360-390-406-410-427-428 engines
Baffled for breather system compatibility
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$532.99

The street Pro-Billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire RPM range of your engine and is completely maintenance-free.

Product Features:

Billet housing 5/8 in. smaller dia. than stock Ford distributors
CARB E.O. Approved
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
QPQ coated polished steel shaft; guided by sealed ball bearings

from

$455.99

The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.

Product Features:

Improved Combustion And Economy
Increased Spark Plug Life
Improved Cold Weather Starting
Maintenance Free Operation
Accurate Spark Timing
Self-Lubricating Bushings
Years Of Trouble-Free Service

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.