1965 Dodge A100 Differentials

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Product Features:

• Each LuK GearBOX contains all the OE quality bearings needed for a professional transmission repair
• LuK Differential Bearing Kits are designed to meet or exceed OEM requirements. This will ensure customer satisfaction.
• LuK Differential Bearing Kits contain the bearings and seals needed to complete the job.
• LuK Differential Bearing Kits include wear parts such as seals, O-rings, shaft sealing rings, support bearings and spare parts where necessary for eliminating the specific cause of failure.

USA Standard Gear open spider gear set for Chrysler 8.25″, 27 spline .

Product Features:

• Spider gear kit
• Fits Chrysler 8.25″ 27 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

8.25″ Chrysler pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Chrysler 8.25″

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon extra HD yoke for Chrysler 8.75″ with 10 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 8.75″
• 10 spline
• 1350 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.188″ cap diameter
• Strap style

Product Features:

• Driven plate
• Fits Dana Spicer 44 Powr Lok

7.25″ & 8.25″ Chrysler pinion seal.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 7.25″ and 8.25″

Product Features:

• BILLET HP 1350-29 SPLINE YOKE

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

• Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Side gear thrust washer kit for 8.25″ Chrysler, 27 spline only.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 8.25″ with 27 spline axles

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a coarse spline pinion which takes a 10 spline yoke.

Product Features:

• Fits Chrysler 8.75″ “42” case housing
• 8.75″ ring gear diameter
• 10 spline pinion
• 12 ring gear bolts
• 4.11 ratio

The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 27 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Product Features:

• Dropout housing
• Fits Chrylser 8.75″
• ’89’ case design
• Nodular iron for added strength

Yukon yoke for Ford 8.8″ truck or passenger with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 8.8″
• 30 spline
• 1330 u-joint size
• 3.625″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• Strap style

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Fits Chrysler 8.25″
• Steel

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

• Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
• 0.495″ tall

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion