1964 Plymouth Barracuda Drivetrains
More 1964 Plymouth Barracuda Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1964 Plymouth Barracuda, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1964 Plymouth Barracuda Drivetrains
USA Standard Gear – Master Overhaul Kit For Chrysler 8.75" #42 Housing With LM104912/49 Carrier Bearings (Part No.37090)
from
$441.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″ ’42’ case housing with LM104912 carrier races
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
Yukon Gear – Spindle Nut Retainer For Dana 60 & 70, 1.830" I.D., 10 Outer TABS (Part No.33477)
from
$10.99
Spindle nut retainer for Dana 60 & 70, 1.830″ I.D., 10 outer tabs. This replaces Spicer part number 30637.
Product Features:
See More
Product Features:
- Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
- 1.830″ I.D.
- 10 outer tabs
Yukon Gear – 1541H Alloy Rear Axle For Chrysler 8.75" (Part No.21408)
from
$284.99
Yukon 1541H alloy cut to fit rear axle for Chrysler 8.75″ measuring 28″-32″ with 30 splines and 5×4.5 bolt pattern. for use with A, C & E-Body. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- 30 spline
- Cut to length design fits 28″-32″ applcations
- 5 x 4.5″ bolt pattern
Yukon Gear – Yoke For Chrysler 8.75" With 29 Spline Pinion And A 7260 U/Joint Size (Part No.41007)
from
$188.99
Yukon yoke for Chrysler 8.75″ with 29 spline pinion and a 7260 U/joint size. 3.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- 29 spline
- 7260 u-joint size
- 2.125″ snap ring span
- 1.078″ cap diameter
- Inside snap ring design
- Strap style
Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)
from
$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
Yukon Gear – The Carrier Bearing Puller (Part No.56034)
from
$689.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
- Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41026)
from
$179.99
Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1350 u-joint size
- 3.625″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Replacement Trail Repair Kit For Dana 60 With 1350 Size U/Joint And U-Bolts (Part No.32284)
from
$239.99
Yukon replacement trail repair kit for Dana 60 with 1350 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 1350 u-joint size
- Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker
Powertrax – Lock Right Locker (Part No.1240-LR)
from
$456.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
Motive Gear – Differential Gear Install Kit (Part No.C8.25IK)
Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)
from
$4.99
Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.
Product Features:
See More
Product Features:
- Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
- 1/2″ x 18 thread
National – Bearings (Part No.M804049)
from
$38.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
National – Bearings (Part No.HM88649)
from
$21.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
National – Shaft Repair Sleeve (Part No.99168)
from
$36.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Yukon Gear – Standard Open Spider Gear Kit For ’96 And Older 8.25" Chrysler With 27 Spline Axles (Part No.16002)
from
$301.99
Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Chrysler 8.25″ open differntial with 27 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – Fill Plug For Chrysler 8.75", 3/4" Thread (Part No.33462)
from
$9.99
Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality
Product Features:
See More
Product Features:
- Fill plug
- Fits Chrysler 8.75″
Yukon Gear – Dana 60 Semi-Float C-Clip (Part No.33247)
National – Multi Purpose Seal (Part No.9376)
from
$7.29
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Yukon Gear – Rubber Fill Plug For Chrysler (Part No.33463)
Yukon Gear – 7.25" & 8.25" Chrysler Pinion Seal (Part No.30189)
from
$16.99
7.25″ & 8.25″ Chrysler pinion seal.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Pinion seal
- Fits Chrysler 7.25″ and 8.25″
Yukon Gear – Dana 60 Pinion Gear Thrust Washer, Standard Open & Tracloc (Also 8.75" Chrysler Std) Dana 70 2Pc (Part No.33287)
from
$5.99
Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.
Product Features:
See More
Product Features:
- Pinion gear thrust washer for Dana Spicer 60
- Fits standard open and Trac Loc applications
Yukon Gear – Chrysler 8.75" Rear Axle Bearing And Seal Kit (Part No.10047)
from
$142.99
Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing with inner and outer seals (one side) for 8.75″ Chrysler. This axle bearing & seal kit services one side only.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″ rear
- Includes axle bearing and inner and outer axle seals
- Services one side
Dorman – Spindle Washer – I.D. 16.7mm O.D. 34.0mm Thickness 3.2mm (sold by each) (Part No.618-021)
from
$7.79
Our Spindle Nut Washers are coated for high corrosion resistance and a long service life. Depending on the application, they are also available in a kit that includes the nut, washer, and retainer.
Product Features:
See More
Product Features:
- Direct replacement for a proper fit every time
- Conveniently available in packs of different quantities
- Durable steel construction
- Dorman’s Spindle Nut Washers are designed and constructed to strict engineering quality standards
Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)
from
$9.99
Chrysler 8.75″ (coarse spline) pinion nut washer.
Product Features:
See More
Product Features:
- Pinion nut washer
- Fits Chrysler 8.75″ with 10 spline pinion
Motive Gear – Differential Carrier (Part No.C9.25E)
National – Bearings (Part No.LM104912)
from
$15.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)
from
$67.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Powr Lok button kit
- Fits Dana Spicer 30, 44 and Chrysler 8.75″
USA Standard Gear – Replacement Ring & Pinion Gear Set For Dana 60 In A 4.11 Ratio (Part No.36075)
from
$391.99
USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.
Product Features:
See More
Product Features:
- Fits standard rotation Dana Spicer 60
- 9.75″ ring gear diameter
- 29 spline pinion
- 12 ring gear bolts
- 4.11 ratio
Popular 1964 Plymouth Barracuda Drivetrains Categories
1964 Plymouth Barracuda Drivetrains
You count on your 1964 Plymouth Barracuda to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 191 Drivetrains ranging in price from $2.49 to $919.99, you’re sure to find everything you need for your 1964 Plymouth Barracuda.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 12 different brands like Driveworks, Yukon Gear, and National. 1964 Plymouth Barracuda Drivetrains start as low as $2.49!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 137 extensive product reviews on 1964 Plymouth Barracuda Drivetrains. Some of the top-rated Drivetrains products we carry are Universal Joint with 4.8 stars and Bearings with 1.0 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1964 Plymouth Barracuda below to get started!
Top-Rated Drivetrains Brands For Your 1964 Plymouth Barracuda
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1964 Plymouth Barracuda running right for years to come. In our inventory you’ll find brands like Driveworks, Yukon Gear, National, and even more.
Popular Dorman Drivetrains
You’ll find popular Dorman brand products across Spindles. All are waiting to get your 1964 Plymouth Barracuda back on the road. Some of the top-rated Dorman products in these categories are:
from
$4.99
(3)
Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm
Spindle Retainers
Top-Rated Driveworks Drivetrains
If Driveworks are what you’re looking for, our inventory holds plenty. We stock Driveworks brand Drivetrains for your 1964 Plymouth Barracuda, and some of our most reviewed Driveworks parts include:
FAQs for 1964 Plymouth Barracuda Drivetrains
What are the most purchased Drivetrains for the 1964 Plymouth Barracuda?
Out of 191 Drivetrains for the 1964 Plymouth Barracuda, the most popular in our inventory are:
What are the top-rated 1964 Plymouth Barracuda Drivetrains?
Top-rated Drivetrains for your 1964 Plymouth Barracuda based on customer reviews/ratings are:
from
$26.99
(1)
Greaseable Premium Universal Joint
“the u-joint itself fit fine however the grease fitting is too large for the hole provided in the u-joint. I had to enlarge the hole to fit the fitting”
