from

$653.99

High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability

from

$29.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features:

Made from HYPER-Flex Polyurethane
Allows Vehicle to Work At Maximum Efficiency
Easy to Install
Superior Performance and Greater Longevity
Lasts Much Longer Than OEM Rubber End Links

from

$647.99

If you’re looking for a performance distributor for your Buick or Nailhead your search is over! MSD’s Ready-to-Run distributor incorporates a magnetic pickup that never wears out! Plus, the distributor has a built in ignition module so there is no need to mount an external MSD Ignition control. Not only do you get the benefits of electronic triggering, but your engine will awaken with the powerful sparks from the ignition module. This module delivers up to 7.5 A to the coil creating a stout inductive spark. This improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance! Another advantage of an MSD distributor is the accurate and adjustable mechanical advance assembly. The advance curve is easy to adjust with different advance springs and stop bushings which are included. To top it off there is a vacuum advance canister and MSD’s strong cap and wire retainer.

Product Features:

Simple and clean three wire installation
CARB E.O. Approved
Does not require an MSD Ignition Control
Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
Mech. advance assem. can be locked out for crank trigger systems
QPQ coated polished steel shaft; guided by sealed ball bearings
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

Universal Floor Mount Application
Base Trimmed For Custom Fit
Cable Operated
Quick Installation
Accurate Shifting

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$10.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Lasts Longer
Looks Great

from

$79.99

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.

Product Features:

10-15% More Energy
Direct Plug In Replacement Direct OE Fit
Advanced Bobbin Technology
Highly Specialized Silicone Magnetic Steel Cores
Standard Motor Products SMP DR-37
MSD 8226
Resist Corrosion
W/New Mounting Hardware

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$154.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$494.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$128.99

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

Heavy Duty 8.8mm Oversized Silicone Jacket
500 Ohms/ft. Of Resistance
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$17.09

Distributor Condenser

from

$55.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$59.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$14.99

Replaces original equipment GM (General Motors) breather #6421868 on 1965-1967 GM (General Motors) big block engines.

Product Features:

Internally baffled with filter
Fits valve cover openings with 1.22¿ dia.
Fits valve cover openings with 1.22┐ dia.
Replaces OEM – GM breather #6421868 on 1965-67 GM Big Blocks
2-1/8¿ tall x 2-1/2¿ dia.
2-1/8┐ tall x 2-1/2┐ dia.

from

$223.99

Product Features:

GM 10BL 7.5 &7.625 R/P 3.73 MGP 10 3/8 X 18 LH THRED BLTS, PD=1.438

from

$73.99

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$665.99

Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:

3400-3800 RPM
Small And Big Blocks
Serious Performance
Furnace Brazed
Fully Balanced

from

$105.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$394.99

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
Manual Choke
4 Barrel Count
Square Bore
Smooth Secondary Transition
Both Timed and Full Vacuum Ports
Includes PCV Outlet

from

$427.99

Product Features:

Satin Finish
4 Barrel
Annular Booster Type
Electric Choke Type
750 cfm Maximum Flow Rating

from

$24.99

Product Features:

Made from HYPER-Flex Polyurethane

from

$24.99

Product Features:

Made from HYPER-Flex Polyurethane

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$23.99

These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features: