1962 Ford Sunliner Performance and Racing Products
More 1962 Ford Sunliner Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1962 Ford Sunliner, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1962 Ford Sunliner Performance and Racing Products
Edelbrock – Sure Seat Valve Springs for Ford 390-428 FE V8 1961-1976 (Part No.5806)
from
$72.99
Product Features:
See More
- Non-Rotator Type
- 1.458 in. Outer Diameter
- 1.062 in. Inner Diameter
- 1.062 in. Coil Blind
- Set of 16
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1246)
from
$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
- Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
- Standard and Low riser
- Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Valve Cover Gasket Set (Part No.276)
from
$25.99
Thick, molded rubber with steel carrier. Manufactured from high-density cork and rubber blend gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage. Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Available in standard or extra thick to provide additional valve train to cover clearance. For OE replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Made from cork/rubber compound
- Can be reused many times
- Thick; fuel-resistant
Hooker Headers – Super Comp. Header (Part No.6205-1HKR)
from
$1296.99
Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.
Product Features:
See More
Product Features:
- Long Tube Lengths
- Long Transition Collectors
- Monstrous Low-Mid Range Torque
- Keep Top End Horsepower
- Provides Finest Fit
- Most Durable Design Available
Edelbrock – Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (200-300-400+ Hp) (Part No.70056)
from
$1243.99
Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.
Product Features:
See More
Product Features:
- Designed For Carbureted V8 Engines
- Power Increases From 200-400_ HP
- Simple To Install
- Shorter Spray Bars
- More Even Distribution Across The Plenum
- A More Balanced Air/Fuel ratio
- Quicker Response Time
Edelbrock – Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9906)
from
$397.99
Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.
See More
B & M – Automatic Shifter, Unimatic Shifter (Part No.80775)
from
$259.99
The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.
Product Features:
See More
Product Features:
- Ideal As Column Shift Replacement
- Includes Neutral Safety Switch
- Includes Black T-Handle
- Backup Light Not Available
- Includes 5 ft. Cable and Hardware
- Includes Boot and Plate
Spectre – Valve Cover (Part No.5266)
from
$52.99
Spectre’s chrome valve cover is designed for 1960-80 Ford 194, 230, 250 and 292 straight 6 cylinder engines. Made from triple chrome-plated steel, this valve cover is stock height and as well as baffled to provide optimum function. Spectre valve covers are engineered to look great as a replacement stock valve cover or as a custom build.
Product Features:
See More
Product Features:
- Designed for 1960-80 Ford 194, 230, 250 and 292 straight 6 cylinder engines
- Baffled design
- Steel construction with chrome-plated finish
- Stock height
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2901)
from
$31.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
Fram – High Perf. Full-Flow Lube Spin-on (Part No.HP1)
from
$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**
Product Features:
See More
Product Features:
- Proven protection for up to 10,000 miles
- Engineered for use with synthetic or conventional motor oils
- Filter media is a blend of fiber and resin that captures 95% of the dirt particles
- The perfect balance of dirt-trapping efficiency and dirt-holding capacity
Proform – Ford HEI Distributor, Red Cap, For Ford 289-302 V8 Engines (Part No.66969R)
from
$228.99
Fits Ford 289 – 302 (5.0). Utilizing the durable and dependable High Energy Ignition (HEI) system pioneered by GM, these distributors avoid the unsightly wiring of stock Ford electronic ignition systems by installing this one-piece distributor with an internally positioned coil and module. Easy to install: just connect one 12-volt hot wire to the distributor (has optional tach hook-up). These units offer calibrated advance curves that are optimized for maximum combustion efficiency and for the elimination of detonation damage and throttle ping. Assembled from precision-madeparts for advance curve smoothness. Offers longer term durability and a higher voltage spark that permits a bigger spark plug gap, resulting in more power and reduced plug fouling. Each unit includes a high-power coil, a premium hi-dielectric cap with brass terminals, and a low-saturation ignition module. By eliminating the stock-Ford ballast resistor, more ignition voltage results in improved spark. Incorporates easily found High Energy Ignition (HEI) replacement parts. Assembled with upper and lower bushings (stock Ford distributors have only a single bushing). Technical Note: Gear not compatible with roller cams. If using roller cams, please contact the cam manufacturer for proper gear selection.
Product Features:
See More
Product Features:
- Street/Strip Version
- Built-In Coil with Magnetic Trigger
- Features Red Cap
- Fits Ford 289-302 5.0 Engines
- Comes with An Iron Gear and with Not Work with Factory Roller Cams
Hooker Headers – Super Competition Header Gasket (Part No.10827HKR)
from
$18.99
Hooker’s precision-matched Super Competition header gaskets provide a sure fit and unmatched exhaust sealing. This OEM quality gasket is constructed of a thick ,.060 inch, high temperature, non-asbestos fiber laminate with a perforated steel core, which provides a superior grip and adhesion. This construction also contributes to exact fit compliance between the cylinder head and header flange, offering excellent sealing properties during extreme temperature and operating conditions.
Product Features:
See More
Product Features:
- Tear Resistant
- Precisely Cut To Match Header
Richmond Gear – RngPnn (Part No.49-0038-1)
from
$577.99
RngPnn
Accel – Contact And Condenser Kit (Part No.8203)
from
$81.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.
Product Features:
See More
Product Features:
- High Performance Points and Condenser
- With Integral Conductor
Spectre – Water Neck; Ford 390-428 (Part No.4736)
from
$47.99
Spectre’s Ford water neck fits Ford 390, 427 and 428 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.
Product Features:
See More
Product Features:
- Fits Ford 390, 427 and 428 engines
- Includes bolts and gasket
- Chrome plated
- Easy to install
MSD Ignition – Coil; Blaster 2; High Performance (Part No.8202)
from
$71.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.
Product Features:
See More
Product Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
Edelbrock – F-28 Dual-Quad; Intake Manifold (Part No.54351)
from
$668.99Product Features:
- Excellent Performance
- Hot Looking Package
- 2 Edelbrock Carbs In-Line
- Progressive Throttle Linkage
- Braided Fuel Line
- Low-Profile Design
- Adequate Hood Clearance
- Maintains Great Drivability
Mallory – Distributor Wiring Harness (Part No.29349)
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1809)
from
$25.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)
from
$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Radiator Cap (Part No.2481)
from
$16.99
Cap off your radiator with a gleaming chrome plated filler cap. Made to last.
Product Features:
See More
Product Features:
- Chrome radiator caps
- Made to last
- Skin packaged
Mr. Gasket – Thermocap Radiator Cap (Part No.2470S)
from
$54.99
Knowing your coolant temperature can help to prevent burn injuries. Thermo Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermo Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Check the Thermo Cap temperature indicator to determine if the coolant is cool enough to make removing Thermo Cap safe. If the coolant is very hot, then thoroughly rinse the radiator with cool water, until the coolant temperature drops into a cooler safe zone Thermo Cap’s integrated coolant reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree Fahrenheit temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges. Chromed crown with a colored trim ring. Indicates coolant temperature, Helps to prevent coolant injuries, integrated coolant reclamation valve, Improves under hood appearance, Fits most domestic or import vehicles and various valve pressures available.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps to prevent coolant injuries
- Integrated coolant reclamation valve
- Improves under hood appearance
- Fits most domestic vehicles
- Built in calibrated thermometer
Mr. Gasket – Oil Pan Bolt Kit (Part No.6088)
from
$18.99
Oil Pan Bolt Kit
Mr. Gasket – Oil Pan Bolt Kit (Part No.6087)
from
$25.99
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.
Product Features:
See More
Product Features:
- Ideal For Tight Spaces
- Serrations Prevent Loosening
- Flange Distributes Pressure
- Zinc Plated Bolts
- Grade 5 Material
- Easy Installation
Edelbrock – TIMING CHAIN (Part No.7844)
Edelbrock – Hex-A-Just By Cloyes Adj. True-Roller Timing Chain Set (Part No.7335)
from
$185.99Product Features:
- Dial-In Your Camshaft With Ease
- Made From Induction Hardened Billet Steel
- Solid Bushing Chain Resists Stretching
- Billet SAE-1144 Steel Crank Sprockets
- Multiple Keyways
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)
from
$51.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Mr. Gasket – Head Gasket (Part No.1132G)
from
$35.99
With the ever-increasing technology in performance and racing engines, supercharged, turbo charged, nitrous-oxide and extreme compression ratios, a demand was created for stronger, more durable engine gaskets. Mr. Gasket, the originator of high performance gaskets, has met the challenge and developed performance gaskets in a variety of materials for all applications to meet the sealing demands of these engines. Mr. Gasket engine gaskets are the most advanced, tested and proven in the performance market today and earned the respect of many professional and sportsman racers.
Product Features:
See More
Product Features:
- Embossed copper
- Provides excellent stability and reduces cyl distortion
Popular 1962 Ford Sunliner Performance and Racing Products Categories
1962 Ford Sunliner Performance and Racing Products
You count on your 1962 Ford Sunliner to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 91 Performance and Racing Products ranging in price from $10.49 to $1,296.99, you’re sure to find everything you need for your 1962 Ford Sunliner.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 14 different brands like K&N, Accel, and FEL-PRO Performance. 1962 Ford Sunliner Performance and Racing Products start as low as $10.49!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 524 extensive product reviews on 1962 Ford Sunliner Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Coil; Blaster 2; High Performance with 4.3 stars and Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) with 3.8 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1962 Ford Sunliner below to get started!
Top-Rated Performance and Racing Products Brands For Your 1962 Ford Sunliner
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1962 Ford Sunliner running right for years to come. In our inventory you’ll find brands like K&N, Accel, FEL-PRO Performance, and even more.
Popular K&N Performance and Racing Products
You’ll find popular K&N brand products across Performance Oil Filters. All are waiting to get your 1962 Ford Sunliner back on the road. Some of the top-rated K&N products in these categories are:
from
$17.99
(23)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
Top-Rated Accel Performance and Racing Products
If Accel are what you’re looking for, our inventory holds plenty. We stock Accel brand Performance and Racing Products for your 1962 Ford Sunliner, and some of our most reviewed Accel parts include:
FAQs for 1962 Ford Sunliner Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1962 Ford Sunliner?
Out of 91 Performance and Racing Products for the 1962 Ford Sunliner, the most popular in our inventory are:
from
$33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
from
$456.99
(45)
Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny
Performance Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Performance Carburetors
What are the top-rated 1962 Ford Sunliner Performance and Racing Products?
Top-rated Performance and Racing Products for your 1962 Ford Sunliner based on customer reviews/ratings are:
from
$397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
“easy to install all the gaskets and parts came with it”
from
$16.99
(4)
High Perf. Full-Flow Lube Spin-on
“Filter size for my boat. OMC 460. works fine. HP filters have a bypass so that clogs do not cause the engine to starve for oil… important for HP eng”
