1961 Ford F-250 Pickup Performance Ignition Products

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

• Bolt-on Performance
• Factory replacement coil

Designed to be used with late model Ford waste spark ignition systems. 83:1 turns ratio and lower primary resistance produce high voltage output. Secondary towers designed for snap on spark plug terminals. Primary terminals require Ford style connector. Carb O.E. approved.

Product Features:

• Designed to use w/late model Ford waste spark ignition systems
• 83:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Secondary towers designed for snap on spark plug terminals
• Primary terminals require Ford style connector

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

• 42000 Volts
• Effective To 6500 RPM
• Quicker Starting
• Improved Throttle Response
• Higher RPM Power
• Can Finished In Yellow

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Using MSD’s DIS-4 ignition systems on your coil-on-plug Ford has always been a great upgrade, but honestly, the wiring poses quite a challenge. To ease this install, we now offer a wiring harness kit that’ll make the install nearly a direct plug-in. The harness provides a splice-free installation with connectors that plug directly into the factory unit. They even have corresponding wire colors. When used in conjunction with two DIS-4 ignitions and four dual ignition Adapters, PN 89121, your coil-on-plug Ford will receive all the spark it needs plus a two-step rev limit and step retard. And the best part is wiring will only take about an hour.

Product Features:

• Easily install two DIS-4 Ignitions on late model Ford Engines
• Easy Connections w/No Splicing Or Cutting Into Factory Wiring
• Wiring the system will take only an hour
• Multiple direct plug in connectors
• Wiring the system will only take and hour

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Product Features:

• Service Part
• Makes Connections Quick And Easy

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

• Heavy Duty 8.8mm Oversized Silicone Jacket
• 500 Ohms/ft. Of Resistance
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Bolt-on Performance
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications

These ACCEL wire sets are custom tailored for true street and strip performance use. Features oversize 8.8 mm ultra performance wires and spark plug boots, 550 degrees Fahrenheit double silicone construction with fiberglass braid. Spiral wound steel core conductor.

Product Features:

• 8.8mm Graphite Suppression
• Silicone Spark Plug Boots
• 550 Degree Double Silicone Construction
• Fiberglass Braid
• Carbon/Graphite Core
• Magnetic Suppression
• Fiberglass/Kevlar Core
• 500 Ohms Resistance

Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:

• High Performance Points and Condenser
• With Integral Conductor

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

• Extra Thick Contact Arms
• Large Radius Tungsten Contacts
• High Strength Phenolic Rubbing Blocks
• Prevents Points Float
• Moisture-Proof Buna-N Condenser

MSD Ignition control are easy to install, but we also offer several plug-in harnesses. These are especially handy for quick installation on late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD. Two wires go from the MSD to the battery and you’re done with no cutting or splicing!

Product Features:

• Splice free installation
• Plugs directly into factory coil

Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features:

• Most Accurate Ignition Timing System
• Improves Performance And Fuel Economy
• Easy To Install With Simple Hand Tools
• Reduced Maintenance
• Eliminates Changing Points