from

$51.99

Stamped steel muscle mounts are the ideal alternative to noisy, vibrating solid mounts. Heavy gauge steel frame and engine brackets are vulcanized to hard durometer rubber. Safety interlock design eliminates need for torque straps or cables. GM application, see catalog for specific vehicle listing.

Product Features:

Without Noise Or Vibration
Heavy Gauge Steel Frame
Safety Interlock Design
No Need For Torque Straps/Cables
Ideal For Replacing Old Mounts

from

$22.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$60.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$30.99

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

One-piece design
Eliminates potential leaks
Prevents over tightening
Prevents torque loss

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$136.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$40.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$25.99

The grade 8 bolts feature high hex head to prevent socket slippage. The thick parallel ground washer allows accurate uniform torque. Black finished, complete with split lock washer to prevent loosening.

Product Features:

These are have a zinc dichromate finish
Tall hex head bolt to prevent slippage
Extra thick parallel ground washer
Washers provides more accurate and uniform torque
Grade 8 alloy steel

from

$14.99

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

2 in. adjustable range
Includes necessary hardware
Chrome plated
Individually packaged

from

$36.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.
Not intended for use in emission controlled vehicles.

from

$245.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Replacement crank trigger wheel for small block Chevy
Absolutely the most accurate way to trigger the ignition
The non-magnetic pickup cannot be false triggered
Powerful magnets are embedded in a billet aluminum trigger wheel

from

$72.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$157.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

3/8″ Diameter, 7.800″ Length
Magnum Pushrods for Small Block Chevy
One-piece .080″ wall chromemoly steel tubing
Heat-treated for extended durability and guide plate compatibility
Precision formed and reinforced pushrod end

from

$299.99

Product Features:

Hi-Ram; Intake Manifold Runner Section

from

$9.99

Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.

Product Features:

Rolled Edges For Strength
Ideal For Magnetos
Ideal For Ignition Distributor

from

$56.99

This chrome plated water neck is precision die cast for a great fit. It features an O-ring style seal to prevent water leaks. These water necks are first polished to a high luster then chrome plated for lasting beauty.

Product Features:

Chrome plated aluminum
O-ring style to prevent leaks
Swivels for hard to fit applications
Comes with allen head bolts

from

$77.99

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

Sure-lock rocker arm nuts
Precise valve train adjustment
Keep rocker arms locked
High-quality grade steel
Heat-treated for ex strength
Plated with durable gold tone finish

from

$12.99

Grade 8, single bolt. Black plated finish. The washers are designed to secure the Mr. Gasket cam button pn1180, pn1181, and pn1183 or can be used as stock replacements.

Product Features:

Specialty and drive train fastener
Special cam bolts
Black plated finish

from

$402.99

Edelbrock #88503 Water Pump big block Chevy short black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pu

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.750 in. Block To Hub Height
Black Finish

from

$125.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$17.99

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

Internally battled
High-porosity filter
Ideal for high performance
Includes rubber grommet

from

$25.99

TIMING COVER SEAL

from

$150.99

BodyMntBshKt

from

$81.99

Spectre’s high quality crankshaft, alternator and engine pulley sets are designed to help dress up your engine compartment. All of our pulleys are designed to work in OE applications and with the OE style serpentine or v-belt configuration.

Product Features:

Engine pulleys come in a chrome or polished finish
Designed for OE engine setup
Looks great
Easy to install

from

$74.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$119.99

Spectre’s Engine Dress-Up Kit was designed for the ’58-’86 Chevrolet small block 265-400. This kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stainless steel braided PCV hose with red/blue Magna-Clamps. Designed for use with OE specifications for fit and function, Spectre products are engineered to perform as good as they look.

Product Features:

For Chevrolet small block 265 and 400
Kit includes: stock height baffled covers, chrome T-bar hold downs, chrome PCV breather, chrome breather, chrome oil filler cap, grommets, and a stain
Designed for use with OE specifications for fit and function
Made from high quality material

from

$3779.99

Product Features:

Develop 400 To 450 Plus Horsepower
Low Profile Design For Good Conscious Rodders
Increases Torque For Heavy Cars And Towing Apps.
Great Power Adder For Low Compression Crate Motors
Various Snout Lengths For Different V-Belt Arngm.
Full Time Power Every Time You Hit The Gas
w/No Lag

from

$25.99

Made of high durometer, very firm, Hyper-Flex performance polyurethane. They’re economical, increase efficiency and are easy to install. Use Energy Suspension sway bar end links with sway bar bushings to get the maximum performance benefit. Combine both for the same effect as buying a larger sway bar. Together they offer a dramatic improvement in performance and handling.

Product Features: