1960 Dodge WM300 Power Wagon Performance and Racing Products
More 1960 Dodge WM300 Power Wagon Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1960 Dodge WM300 Power Wagon, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1960 Dodge WM300 Power Wagon Performance and Racing Products
Hurst – B-1 Shifter Boot and Plate (Part No.1147336)
from
$42.49
Designed for use with round stick shifters. Complete with chrome ID plate and mounting hardware. Measures: 4-3/8 in. x 5-3/8 in. with 3 pleats.
Product Features:
See More
Product Features:
- Complete with Mounting Hardware
- Adapt To Most Shifter Install
- Hurst Quality
- Works Well with Round Shift Levers
- Chrome ID Plate
Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)
from
$27.49
These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.
Product Features:
See More
Product Features:
- Assures Accurate Torque App
- Prevents Galling Manifold
- Grade 5 Material
- Black Oxide Coasted
Edelbrock – RPM Air-Gap Small Block Chrysler Black Intake Manifold (Part No.75763)
from
$612.99
Edelbrock part #75763 RPM Air-Gap intake manifold is designed for 340-360 c.i.d. Chrysler V8’s and 318 c.i.d. engines with 340-360 cylinder heads. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competit
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.9 in. Front Height, 5.35 in. Center Height, 5.8 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Earls Performance Product – Solo Bleed (Part No.280021ERL)
from
$32.59Product Features:
- Prevents Air Inclusion
- Direct Replacement
- For OE Bleeders
- One Person Bleeds Safely
- Without The Mess
- No Chance Of Air Bubbles
Edelbrock – Sure Seat Valve Springs for Chrysler 318-340-360 V8 1957-89 (Part No.5877)
from
$59.99
Product Features:
See More
- Non-Rotator Type
- 1.394 in. Outer Diameter
- 1.010 in. Inner Diameter
- 1.010 in. Coil Blind
- Set of 16
Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 180 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$27.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – Remote Oil Filter Kit (Part No.7682)
from
$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.
Product Features:
See More
Product Features:
- Relocate oil filter to an easy access location
Fram – High Perf. Full-Flow Lube Spin-on (Part No.HP1)
from
$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**
Product Features:
See More
Product Features:
- Proven protection for up to 10,000 miles
- Engineered for use with synthetic or conventional motor oils
- Filter media is a blend of fiber and resin that captures 95% of the dirt particles
- The perfect balance of dirt-trapping efficiency and dirt-holding capacity
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Distributor Wiring Harness (Part No.29349)
Flowtech – Header Gasket Set (Part No.99361FLT)
from
$18.59
Header Gasket Set
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Mr. Gasket – Oil Pan Bolt Kit (Part No.6088)
from
$18.99
Oil Pan Bolt Kit
Mr. Gasket – Dust Cap (Part No.2485)
from
$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Set of 2 Caps
- Easy Installation
- 2 Per Set
Edelbrock – Performer RPM Series fuel pump is for Small-Block Chrysler (Part No.1720)
from
$209.99
Edelbrock part #1720 Performer RPM Series fuel pump is for Small-Block Chrysler designed for use with all Edelbrock carburetors used in Performer or Performer RPM applications. These high-performance’s street Fuel Pumps feature a high quality three stage
See More
Holley – Mechanical Fuel Pump Mounting Pad Cover (Part No.12-813)
from
$17.79
Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.
Product Features:
See More
Product Features:
- Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S
Popular 1960 Dodge WM300 Power Wagon Performance and Racing Products Categories
1960 Dodge WM300 Power Wagon Performance and Racing Products
You count on your 1960 Dodge WM300 Power Wagon to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 18 Performance and Racing Products ranging in price from $12.09 to $612.99, you’re sure to find everything you need for your 1960 Dodge WM300 Power Wagon.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 8 different brands like Mr. Gasket, Fram, and Flowtech. 1960 Dodge WM300 Power Wagon Performance and Racing Products start as low as $12.09!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 41 extensive product reviews on 1960 Dodge WM300 Power Wagon Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are B-1 Shifter Boot and Plate with 1.0 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1960 Dodge WM300 Power Wagon below to get started!
Top-Rated Performance and Racing Products Brands For Your 1960 Dodge WM300 Power Wagon
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1960 Dodge WM300 Power Wagon running right for years to come. In our inventory you’ll find brands like Mr. Gasket, Fram, Flowtech, and even more.
Popular Mallory Performance and Racing Products
You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1960 Dodge WM300 Power Wagon back on the road. Some of the top-rated Mallory products in these categories are:
Top-Rated Performance and Racing Products
If are what you’re looking for, our inventory holds plenty. We stock brand Performance and Racing Products for your 1960 Dodge WM300 Power Wagon, and some of our most reviewed parts include:
FAQs for 1960 Dodge WM300 Power Wagon Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1960 Dodge WM300 Power Wagon?
Out of 18 Performance and Racing Products for the 1960 Dodge WM300 Power Wagon, the most popular in our inventory are:
What are the top-rated 1960 Dodge WM300 Power Wagon Performance and Racing Products?
Top-rated Performance and Racing Products for your 1960 Dodge WM300 Power Wagon based on customer reviews/ratings are:
from
$42.49
(1)
B-1 Shifter Boot and Plate
“The website claims this is an exact fit for my S-10. I have a 5 spd 2.5L 1990 S-10. The boot/plate are about 2/3rds the necessary size to actually mou”
