1957 Buick Roadmaster Performance and Racing Products

Essential 1957 Buick Roadmaster Performance and Racing Products

Accel – Points Eliminator Kit (Part No.2010)

Points Eliminator Kit

from

$105.99
Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • More Accurate Ignition Timing
  • Improves Performance And Fuel Economy
  • Provides More Accurate Ignition Timing
  • Easy To Install w/Hand Tools
  • Reduced Maintenance
  • Thermal Clad Based Surface Mount Construction
  • Utilizes Specialized Electronic Circuitry
  • Ignition Timing Is Stable From 1 To 10000rpm
See More

MSD Ignition – Harness; MSD to Late Model; GMs; 96-on (Part No.8877)

Harness; MSD to Late Model; GMs; 96-on

from

$72.99
MSD Ignition control are easy to install, but we also offer several direct plug-in harnesses for late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD.

Product Features:
  • Plug-In Harness w/Color Coded Wires
  • No Cutting Or Splicing
  • Quick Easy Installation
  • Provides A Direct Plug-In Installation
  • When Adding An MSD Ignition Control
See More

Accel – Hei Remote Mount Super Coil (Part No.140024)

Hei Remote Mount Super Coil

from

$65.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Can also work with CD ignition systems. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Comes complete with new mounting hardware. High dielectric strength ACCEL yellow over molded housing. Output is 48,000 volts with 0.2ohms resistance.

Product Features:
  • Remote Mount Ignition Coil
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Throttle Response
  • More High RPM Power
  • Increase Energy Transfer
  • Resist Corrosion
  • W/New Mounting Hardware
See More

MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)

Coil; GM External HEI Coil; High Performance

from

$71.99
Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:
  • Direct performance replacement for GM dual connector coil
  • 100:1 Turns Ratio
  • Lower Primary Resistance Produces High Voltage Output
  • Works w/Stock Ignition As Well As MSD Ignitions
See More

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)

Mallory Kit: Unil Conv: Delco: V8

from

$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • Easy Installation
  • Improved Fuel Economy
  • Reduced Maintenance
  • Accurate Timing
  • Improved Performance
  • Provides A Simple Conversion
  • No Moving Parts To Wear Out
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Edelbrock – CARBURETOR (Part No.1812)

CARBURETOR

from

$443.99
New qwik-tune adjustable secondary air valve. Optional single or dual fuel inlet. Distinctive black accented hardware. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkag

Product Features:
  • New Qwik-Tune Adjustable Secondary Air Valve
  • Optional Single Or Dual Fuel Inlet
  • Distinctive Black Accented Hardware
  • No Gaskets Below Fuel Level to Prevent Leakage
  • Metering Rod/Step Up Springs Can Be Changed Easily
  • GM/AMC-Style Throttle Linkage
  • Exclusive 12 Month Complete Satisfaction Warranty
See More

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Mr. Gasket – Alternator Bracket (Part No.9850)

Alternator Bracket

from

$25.99
Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:
  • Chrome Plated Steel
  • F-Style
  • Heavy Gauge Steel Construction
  • Fits Small Block Chevy 265-400 CID
  • Must Be Used With Part 9852
See More

Mallory – Distributor Condenser (Part No.401)

Distributor Condenser

from

$17.09
Distributor Condenser

Accel – Contact Set Hp 32 Oz (Part No.110128)

Contact Set Hp 32 Oz

from

$54.39
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:
  • Extra Thick Contact Arms
  • Large Radius Tungsten Contacts
  • High Strength Phenolic Rubbing Blocks
  • Prevents Points Float
  • Moisture-Proof Buna-N Condenser
See More

MSD Ignition – Distributor; Buick Nailhead; Ready-to-Run (Part No.8524)

Distributor; Buick Nailhead; Ready-to-Run

from

$702.99
The Buick Nailhead is one of the most sought after nostalgic engines for rods and is still providing the smooth power to plenty of Buick’s. Nailhead fans can finally get a state-of-the-art distributor to provide the fire! MSD’s Nailhead distributor is a ready to run unit which incorporates a magnetic pickup that never wears out. Plus, the distributor has a built in ignition module so there is no need to mount an external MSD Ignition control. The module delivers up to 7.5 A to the coil creating a stout inductive spark. Not only do you get the benefits of electronic triggering, but your engine will awaken with powerful sparks from the ignition module. This improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance.

Product Features:
  • Simple and clean three wire installation
  • Includes built-in Rev Limiter
  • Does not require an MSD Ignition Control
  • Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
  • Mech. advance assem. can be locked out for crank trigger systems
  • Advance plate and weights are fine blanked from chrome moly steel
  • QPQ coated for friction reduction
  • QPQ coated polished steel shaft; guided by sealed ball bearings
  • Maintenance-free magnetic pickup and precision reluctor
  • Creates stable trigger signals throughout the rpm range
  • CNC machined billet aluminum housing and billet aluminum base
  • Vacuum advance canister for improved economy (can be locked out)
See More

Accel – HEI Distributor Cap & Rotor Kit – Tan – Chevrolet V8 (Part No.8132)

HEI Distributor Cap & Rotor Kit - Tan - Chevrolet V8

from

$47.49
Chevrolet V8 engines with HEI/EST remount mount coil 8132 35362 applications include 1987-93 Cars and 1987-95 Trucks (Supersedes 60110).

Product Features:
  • Features Protection From Arc Thru And Crossfire
  • Features 60K V Rated Alkyd Compound
See More

Accel – Distributor Cap And Rotor Kit (Part No.8124)

Distributor Cap And Rotor Kit

from

$48.49


Product Features:
  • Heavy Duty Cap and Rotor Kit
  • With Brass Inserts
See More

Mr. Gasket – Lts Throttle Cable Brkt Chev (Part No.9885)

Lts Throttle Cable Brkt Chev

from

$14.99
The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:
  • 2 in. adjustable range
  • Includes necessary hardware
  • Chrome plated
  • Individually packaged
See More

1957 Buick Roadmaster Performance and Racing Products

You count on your 1957 Buick Roadmaster to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 15 Performance and Racing Products ranging in price from $14.99 to $702.99, you’re sure to find everything you need for your 1957 Buick Roadmaster.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 5 different brands like Edelbrock, Accel, and Mr. Gasket. 1957 Buick Roadmaster Performance and Racing Products start as low as $14.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 149 extensive product reviews on 1957 Buick Roadmaster Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR) with 4.5 stars and Distributor Cap And Rotor Kit with 5.0 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1957 Buick Roadmaster below to get started!

Top-Rated Performance and Racing Products Brands For Your 1957 Buick Roadmaster

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1957 Buick Roadmaster running right for years to come. In our inventory you’ll find brands like Edelbrock, Accel, Mr. Gasket, and even more.

Popular Mallory Performance and Racing Products

You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1957 Buick Roadmaster back on the road. Some of the top-rated Mallory products in these categories are:
Mallory Kit: Unil Conv: Delco: V8
from $134.99
(1)
Mallory Kit: Unil Conv: Delco: V8
Performance Ignition Parts

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1957 Buick Roadmaster, and some of our most reviewed Edelbrock parts include:

FAQs for 1957 Buick Roadmaster Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1957 Buick Roadmaster?

Out of 15 Performance and Racing Products for the 1957 Buick Roadmaster, the most popular in our inventory are:
Alternator Bracket
from $25.99
(2)
Alternator Bracket
Performance Exhaust Header Hardware
Supercoil
from $105.99
This product is not rated
Supercoil
Performance Coils
Contact Set Hp 32 Oz
from $54.39
This product is not rated
Contact Set Hp 32 Oz
Performance Points and Condensers

What are the top-rated 1957 Buick Roadmaster Performance and Racing Products?

Top-rated Performance and Racing Products for your 1957 Buick Roadmaster based on customer reviews/ratings are:
Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR)
from $427.99
(2)
Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR)
“Put carb on rock crawler. Climb lots of hills and the carb works great. No loss of fuel when climbing steep grade. Does what I bought it to do.”
Distributor Cap And Rotor Kit
from $48.49
(1)
Distributor Cap And Rotor Kit
“Great product and good price”
Points Eliminator Kit
from $105.99
(1)
Points Eliminator Kit
“Replaced point system with the pile of garbage.”