1956 Chrysler Town & Country Performance and Racing Products
More 1956 Chrysler Town & Country Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1956 Chrysler Town & Country, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1956 Chrysler Town & Country Performance and Racing Products
Edelbrock – Performer RPM Series fuel pump is for Small-Block Chrysler (Part No.1720)
from
$209.99
Edelbrock part #1720 Performer RPM Series fuel pump is for Small-Block Chrysler designed for use with all Edelbrock carburetors used in Performer or Performer RPM applications. These high-performance’s street Fuel Pumps feature a high quality three stage
See More
Holley – Mechanical Fuel Pump Mounting Pad Cover (Part No.12-813)
from
$17.79
Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.
Product Features:
See More
Product Features:
- Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S
Holley – Mechanical Fuel Pump (Part No.12-440-11)
from
$206.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.
Product Features:
See More
Product Features:
- High Output Fuel Flow
- Flows 110 gph Free Flow
- Shutoff Pressure Pre-Set From 6.5 To 8 PSI
- Fuel Pressure Regulator Is Not Required
- Heavy Duty Construction For Continuous High rpm Operation
- Fuel Body Casting Can Be Rotated For Plumbing Situations
- Inlet And Outlet Tapped For 1/4 in. NPT
- Inlet/Outlet Tapped For 3/8 in. NPT
Accel – High-Performance Ignition Coil – Direct OE Fit (Part No.140021)
from
$72.39
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, crisper throttle response and more high RPM power. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Standard Motor Products SMP Uf-198
- MSD 8228
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)
from
$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary
Product Features:
See More
Product Features:
- 42000 Volts
- Effective To 6500 RPM
- Quicker Starting
- Improved Throttle Response
- Higher RPM Power
- Can Finished In Yellow
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mr. Gasket – High Performance Thermostat (Part No.4365)
from
$27.49
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 195 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – High Performance Thermostat (Part No.4366)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens at 160 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Stainless Steel, Copper & Brass Construction – Resists Corrosion
- High Flow
Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 180 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Edelbrock – Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.1825)
from
$427.99
The Edelbrock 1825 Thunder Series AVS 650 CFM manual choke carburetor has been designed and calibrated to deliver optimum off-road performance. Several characteristics make the 1825 Thunder Series AVS 650 CFM manual choke carburetor an outstanding street
Product Features:
See More
Product Features:
- Spring Loaded Needles/Seat Increase Performance
- New Qwik-Tune Adjustable Secondary Air Valve
- Distinctive Black Accented Hardware
- Lightweight Ball-Burnished Aluminum
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)
from
$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9906)
from
$397.99
Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.
See More
Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)
from
$498.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Electric Choke Installed from Factory
- Smooth Secondary Transition
- Includes Only Timed Vacuum Port
- Includes EGR ; Fuel Vapor Outlet
Edelbrock – Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9913)
from
$427.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Electric Choke Type
- 750 cfm Maximum Flow Rating
MSD Ignition – Distributor; Chrysler 331; Ready-to-Run (Part No.8391)
from
$713.99
The Pro billet Early Hemi Ready-to-Run distributor earns its name with simple wiring. One wire to 12 V, one to coil negative and another to ground. That’s it! A matching harness with a 3-pin Weathertight connector is supplied. These distributors are the answer to weak breaker points or rebuilt aftermarket models. Inside the billet housing there is a high-output ignition module. When the maintenance-free magnetic pick-up signals the module to fire, up to 7.5 amps is sent to the coil where a powerful spark is created. This improved spark output results in quick starts, snappy throttle response and terrific drivability. The distributors are equipped with a vacuum advance canister for cruising economy. Plus, there is a mechanical advance assembly that is mounted on top of the distributor shaft making it easy to adjust the advance to meet your needs. Another great feature of the ready-to-run distributors is their simple installation. All you need to do is connect three wires and you’ll be cruising.
Product Features:
See More
Product Features:
- Simple and clean three wire installation
- CARB E.O. Approved
- Does not require an MSD Ignition Control
- Supplied w/HEI Style Distributor Cap And Rotor
- Accepts Cap-A-Dapts
- Mech. advance assem. can be locked out for crank trigger systems
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Maintenance-free magnetic pickup and precision reluctor
MSD Ignition – Distributor; Chrysler 383-400; Ready-to-Run (Part No.8386)
from
$654.99
MSD’s Ready-to-Run Pro-Billet distributors for Chrysler engines are the perfect upgrade from breaker points or weak electronic ignitions. These distributors feature a maintenance-free magnetic pick-up that accurately triggers the built-in powerful ignition module. This module produces a high-output spark which improves combustion in the cylinder, resulting in quick starts, a smooth idle and great performance. Just beneath the race rotor is a mechanical advance assembly so a timing curve can easily be tailored to match your application. The QPQ coated shaft is guided by a sealed ball bearing assembly for stability and endurance while a vacuum advance canister helps increase economy on those long cruises. The Ready-to-Run distributors are also a breeze to install. Simply drop it in the engine and connect three wires and you’re Ready-to-Run to your favorite cruise! The front engine mount models are designed in a special small diameter housing to clear aftermarket heads and valve covers.
Product Features:
See More
Product Features:
- Simple and clean three wire installation
- CARB E.O. Approved
- Supplied w/HEI Style Distributor Cap And Rotor
- Accepts Cap-A-Dapts
- Mech. advance assem. can be locked out for crank trigger systems
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
MSD Ignition – Distributor; Chrysler 426; 440 Pro-Billet (Part No.8546)
from
$409.99
MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.
Product Features:
See More
Product Features:
- Smaller diameter CNC machined billet aluminum housing
- Must Be Used w/An MSD Ignition Control
- Supplied w/small dia. cap w/HEI style terminals; race and rotor
- Nylon pads ensure smooth operation of the advance weights
- Advance weight pins are staked and tig welded to the plate
- Mech. advance assem. can be locked out for crank trigger systems
- Advance plate and weights are fine blanked from chrome moly steel
- QPQ coated for friction reduction
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
- Easy-to-adjust mech. advance w/supplied springs and stop bushings
- No CARB Exemption Order Number
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3757801)
from
$538.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
Mallory – Unilite Electronic Ignition Distributor Series 37 (Part No.3757901)
from
$538.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)
from
$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
Popular 1956 Chrysler Town & Country Performance and Racing Products Categories
1956 Chrysler Town & Country Performance and Racing Products
You count on your 1956 Chrysler Town & Country to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 14 Performance and Racing Products ranging in price from $26.99 to $713.99, you’re sure to find everything you need for your 1956 Chrysler Town & Country.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 5 different brands like Accel, Edelbrock, and Mr. Gasket. 1956 Chrysler Town & Country Performance and Racing Products start as low as $26.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 186 extensive product reviews on 1956 Chrysler Town & Country Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR) with 4.5 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1956 Chrysler Town & Country below to get started!
Top-Rated Performance and Racing Products Brands For Your 1956 Chrysler Town & Country
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1956 Chrysler Town & Country running right for years to come. In our inventory you’ll find brands like Accel, Edelbrock, Mr. Gasket, and even more.
Popular Mallory Performance and Racing Products
You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1956 Chrysler Town & Country back on the road. Some of the top-rated Mallory products in these categories are:
Top-Rated Edelbrock Performance and Racing Products
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1956 Chrysler Town & Country, and some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Performance Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Performance Carburetors
from
$397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
Performance Carburetors
FAQs for 1956 Chrysler Town & Country Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1956 Chrysler Town & Country?
Out of 14 Performance and Racing Products for the 1956 Chrysler Town & Country, the most popular in our inventory are:
from
$42.49
(54)
Super Stock Replacement Coil for Improved Performance, Starting, and Power
Performance Coils
from
$26.99
This product is not rated
High Performance Thermostat
Performance Engine Coolant Thermostats
What are the top-rated 1956 Chrysler Town & Country Performance and Racing Products?
Top-rated Performance and Racing Products for your 1956 Chrysler Town & Country based on customer reviews/ratings are:
from
$427.99
(2)
Thunder AVS Carburetor #1825 650 CFM With Manual Choke, Satin Finish (Non-EGR)
“Put carb on rock crawler. Climb lots of hills and the carb works great. No loss of fuel when climbing steep grade. Does what I bought it to do.”
