Volvo 265 Drivetrains

Product Features:

• Cover gasket
• Fits Dana Spicer 30

FAG drive shaft support bearings are built to meet or exceed OE specifications. FAG Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination.

Product Features:

• Original equipment design and quality
• Utilizes OE equivalent or better materials
• Pre-Lubricated and reinforced seals

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 30 rear
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Product Features:

• Seal housing for Dana Spicer 30 and AMC Model 35
• Includes o-rings

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
• 3/4″ x 16 thread

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

Yukon replacement standard open carrier case for Dana 30, 3.73 & up,bare. This case includes carrier shims, roll pin, ring gear bolts and a cover gasket. If purchasing this case for a D30 JK front, you will need to also purchase spider gear set YPKD30-S-27.

Product Features:

• Standard open carrier case
• Fits Dana Spicer 30
• 3.73 and up ratio only
• Does not include spider gears
• Includes ring gear bolts, carrier shim kit, roll pin, and cover gasket

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

The MTC Driveshaft Support Washer is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Premium aftermarket replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

CONE

Application-Specific Engineering Design to ensure the correct fit, function and high performance of the wheel bearing. BCA supplies premium replacement bearings that meet or exceed the OE specifications. Premium Quality Materials are used for forged steel rings, seals, precision cages, rolling elements and premium grease, to ensure that our customers receive a robust, durable product. Seals are customized for each BCA hub based on application-specific materials and design requirements to minimize the chance of contamination and maximize bearing life. Precision Cage on BCA bearings are designed to keep the rolling elements of the bearing spaced correctly. The cages undergo design verification and production validation testing to ensure high quality. Pre-Lubrication of all BCA wheel bearings with premium grease for your convenience. This is a major advantage so you do not have to worry about grease or seal application.

Product Features:

• For wheel bearings, BCA utilizes Forged Steel in the inner and outer rings that meets our stringent steel quality specifications to optimize bearing life.
• For taper bearings, BCA utilizes Case Carburized Steel for heavy duty shock loads and longer life.

ZIP locker switch.

Product Features:

• Switch

Product Features:

• Spider gear kit
• Fits Dana Spicer 30 27 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• Brand may vary by location

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 44
• 26 spline
• 1310 u-joint size
• 3.219″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• U-bolt style

Product Features:

• Fits standard rotation Dana Spicer 30
• Chrome

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 30 rear
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Universal Joint

Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 30 open differential with 27 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

Product Features:

• Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

SHAFT SEAL