Pontiac Star Chief Performance and Racing Products

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes sixteen (16) 3/8 inch-16 x 1-1/4 inch bolts & washers

Product Features:

• Zinc plated Grade 5 steel
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Ideal For Minimal Space
• 12-Point Head And Flange
• Zinc Plated For Protection

Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:

• Vibratory Polished For Good Looks
• Optimized Street Calibration That Works Out Of The Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

Edelbrock part #21563 Performer Pontiac intake manifold is designed for 1965-79 Pontiac 326-455 c.i.d. V8’s (except Ram Air V and 265/301 V8’s). Provides great throttle response for performance you can feel. Ideal for cars, 4x4s, tow vehicles, RVs and boa

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type-4150 Style Flange
• 5.5 in. Front Height, 6.05 in. Center Height, 6.6 in. Rear Height
• Black Powder Coated Finish
• Non-EGR

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

• Ideal For Tight Spaces
• Serrations Prevent Loosening
• Flange Distributes Pressure
• Zinc Plated Bolts
• Grade 5 Material
• Easy Installation

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 2.08 inches in diameter. Two per set.

Product Features:

• Adds the finishing touch to custom wheels
• sold in a pair
• Easy Installation
• 2 Per Set

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

• Glass Filled Polyester Case
• Longer Spark Duration
• Increased Performance
• No Energy Loss Due To Arcing
• Includes Brass Contact Terminal

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Lakewood universal replacement U-joints are fatigue- and wear-resistant, the ultimate in strength. Designed with ultra-durable chrome-nickel-moly alloy cross and caps, and special high-carbon steel and induction heat-treated needle bearings.

Product Features:

• Chrome-Nickel-Moly Alloy Cross
• Improved Fatigue Resistance
• High-Carbon Steel Bearings
• Maximize Wear Resistance
• Solid Forged Cross Body
• High Strength

Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 4.50 in. Block To Hub Height
• Black Finish

Matched assembly for maximum reliability. An excellent choice for high performance street applications.

Product Features:

• Built As Matched Assembly
• Exceptional Performance
• Exceptional Durability
• Long Term Dependability
• Designed for Street And Street Strip Applications

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

• 42000 Volts
• Effective To 6500 RPM
• Quicker Starting
• Improved Throttle Response
• Higher RPM Power
• Can Finished In Yellow

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

• Easy Installation
• Improved Fuel Economy
• Reduced Maintenance
• Accurate Timing
• Improved Performance
• Provides A Simple Conversion
• No Moving Parts To Wear Out

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

This unit permits a seamless wide range of adjustment to both amount and rate of ignition advance. This unit helps increase horsepower and throttle response. It provides maximum spark advance while preventing detonation or “pinging”. This kit includes an allen wrench for easy adjustment along with instructions.

Product Features:

• Adjustable Vacuum Advance
• Increases Horsepower And Throttle Response
• Includes Allen Wrench For Adjustments
• Instantly Increase Horsepower
• Maximum Possible Spark Advance
• Not Legal For Sale/Use In CA

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Can be trimmed if necessary for modified port applications
• Complete with manifold end seals and distributor gasket where applicable
• For OE replacement, high performance street, drag race and oval track use

Constructed of durable polyurethane to handle the stress oh high horsepower. Absorbs vibration and lasts longer than rubber Features unique built-in safety lock to keep from separating under high torque loads. Ideal for use on street or strip applications. Complete with grade-8 mounting hardware.

Product Features:

• Durable Polyurethane
• Absorbs Vibration
• Last Longer Than Rubber
• Built-In Safety Lock

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features:

• Chrome Plated Steel
• F-Style
• Heavy Gauge Steel Construction
• Fits Small Block Chevy 265-400 CID
• Must Be Used With Part 9852

Replaces original equipment GM (General Motors) breather #6421868 on 1965-1967 GM (General Motors) big block engines.

Product Features:

• Internally baffled with filter
• Fits valve cover openings with 1.22¿ dia.
• Fits valve cover openings with 1.22┐ dia.
• Replaces OEM – GM breather #6421868 on 1965-67 GM Big Blocks
• 2-1/8¿ tall x 2-1/2¿ dia.
• 2-1/8┐ tall x 2-1/2┐ dia.

This is a high quality original equipment style breather that will give you that original look and is of a high quality. We recommend this for all applications where the original appearance is necessary.

Product Features:

• Chrome Plated Steel
• Internally Baffled With Filter
• Fits Valve Covers With 1.22 In Opening

This chrome plated breather, or oil filler cap, is internally baffled with filter. Very similar to the original equipment breather used on 1965-1967 Chevrolet 396-427 Big Blocks. GM (General Motors) #6421868. Fits valve cover openings with 1.22 inch diameter. Its overall dimensions are 2-1/8 inch tall and 2-1/2 inch in diameter.

Product Features:

• Integral Metal Baffle
• Grommet Included

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Product Features:

• Best with aftermarket torque converters and 9.5:1 compression.
• Great high RPM power.
• Easy on valve train parts.
• Can be used with mild ratio rocker arms and traditional performance valve springs.