Pontiac Performance Exhaust Products

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four-inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• High Performance
• Affordable
• Durable 16 Gauge Material
• Welds Easier
• Lasts Longer
• Heat Cured
• High Heat Resistant

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

The MagnaFlow Street Series Cat-Back Performance Exhaust System 15693 brings out the personality of your Car with our signature resonant, powerful engine tone and dyno-proven performance. Thanks to its fast-flowing, mandrel bent 2.5in. main piping and 1 Straight-Through mufflers ending in a Dual Split Rear exit with 3.5in. Polished Welded-On Single Wall Angle Cut Cut Edge tips, this Car exhaust kit has the performance chops to match its sporty sound and appearance. Upgrade your ride to the next level with an exhaust that has the pipes to put other Car’s to shame. With this system your vehicle will be producing Moderate exterior and Mild interior sound levels while leaving other cars and trucks feeling envious at every stoplight. Exhaust kit 15693 features a cat-back layout that replaces your ride’s stock exhaust components from near the catalytic converter on back. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 15693 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s 1-year limited finish warranty and limited lifetime construction warranty.

Product Features:

• Dyno-proven performance
• Durable corrosion-resistant stainless steel construction
• CNC precision robotic manufacturing techniques

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

• High-temperature exhaust material
• Withstands extreme exhaust heat
• Provides excellent sealing and durability
• Superior tensile strength
• Resists deteriorating
• Provides excellent torque retention

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

For the person who wants the look of a traditional dual exhaust system with all the benefits that a Flowmaster Cat-back exhaust system provides. D.O.R. (Dual out rear) systems are the perfect choice. American Thunder systems deliver a moderate to aggressive interior and exterior tone and are suited to the enthusiast who wants their performance to be heard. Like all Flowmaster systems, the benefits include improved throttle response, power and mileage. Designed for an easy fit, these systems include all necessary parts and hardware for easy installation.

Flowmaster’s Super 44 muffler uses the same Delta Flow technology found in our larger Super 40 mufflers. The Super 44 delivers a powerful rich tone and is the most aggressive, deepest sounding, highest performing four inch case street muffler we’ve ever built! Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

What sets us apart as a company in the automotive industry? Many things come to mind, but most importantly is our knowledgeable team of employees. They are qualified and dedicated professionals who are experts in the automotive industry, and most are racers and enthusiasts themselves, including Mr. Gasket’s President, Mr. Bob Romanelli. People with first-hand interest and knowledge of this industry, who create and apply new concepts based not only on research and numbers, but on personal experience and hands-on know-how. Our staff of enthusiasts apply their knowledge to product engineering, research and development, product management, and marketing services. Members of our technical service group have an average tenure exceeding fifteen years. That’s not just dedication to a career, that’s commitment to something they truly believe in.

Product Features:

• Withstands intense exhaust heat
• Resists deteriorating
• Easy removal for disassembly

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

• High-temperature exhaust material
• Withstands extreme exhaust heat
• Provides excellent sealing and durability
• Superior tensile strength
• Resists deteriorating
• Provides excellent torque retention

DynoMax® Super Turbo performance mufflers exclusive patented flow director design channels exhaust flow and eliminates turbulence on most applications. The large internal flow tubes improve exhaust flow and reduce backpressure. Each muffler uses fiberglas

Product Features:

• Large internal flow tubes improve exhaust flow and reduce backpressure
• Exclusive patented flow director design channels exhaust flow and eliminates turbulence on most applications.
• Fiberglass matting technology to absorb unwanted interior resonance while maintaining a mellow performance tone
• Dyno proven to flow up to 700 SCFM

The MagnaFlow Street Series Crossmember-Back Performance Exhaust System 15895 brings enhanced engine sound and dyno-proven performance to your muscle car with a healthy helping of our deep, resonant signature exhaust note at Moderate exterior and Mild interior sound levels. Thanks to its durable, corrosion resistant stainless steel design, this exhaust system will handle whatever tarmac you decide to leave your mark on. This performance exhaust kit features a crossmember-back layout designed to replace your exhaust system from the crossmember on back. With its fast-flowing, mandrel bent 2.5in. main piping and 1 Straight-Through mufflers ending in a Dual Split Rear exit that you can enhance with tips of your choosing, your muscle car will be sounding as awesome as it looks. Extensive 3D scanning during development has resulted in a direct-fit design that you can easily install yourself. 15895 is produced using CNC precision robotic manufacturing techniques and is backed by MagnaFlow’s limited lifetime construction warranty.

Product Features:

• Dyno-proven performance
• Durable corrosion-resistant stainless steel construction
• CNC precision robotic manufacturing techniques

Super Competition Cat-Back System Black Finish Mufflers with Aluminized Tubing

Product Features:

• Exit At Stock Locations
• Mandrel Bent Not Press Bent
• Mandrel Bent Not Press Bent
• Maximum Flow
• Uses Existing Stock Hangers
• Large Diameter 16 Ga. Aluminum Tubing
• Low Back Pressure and Long Life
• Easy Installation

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

• Graphite-impregnated facing
• Steel expanded metal core
• Superior tensile strength
• Resists cracking
• Withstands intense heat
• Resists deteriorating
• Anti-stick properties
• Easy removal for disassembly

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

The Original 40 series muffler delivers an aggressive exterior and interior tone. If you’re looking for that original Flowmaster sound this is the muffler is for you. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

• High Performance
• Affordable
• Durable 16 Gauge Material
• Welds Easier
• Lasts Longer
• Heat Cured
• High Heat Resistant

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

• High-temperature exhaust material
• Withstands extreme exhaust heat
• Provides excellent sealing and durability
• Superior tensile strength
• Resists deteriorating
• Provides excellent torque retention

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

The three chamber design utilizes Flowmaster’s patented Delta Flow technology along with an internal tuning chamber to reduce sound inside the vehicle. Provides the same performance and exterior tone characteristics as the two chamber, but with less interior resonance. Constructed of 16 gauge aluminized steel and fully MIG welded for maximum durability.

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

• Withstands intense exhaust heat
• Graphite-impregnated facing
• Steel expanded metal core
• Superior tensile strength
• Resists deteriorating
• Anti-stick properties
• Easy removal for disassembly

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.