Pontiac GTO Automatic Transmission Parts

Pro-King is the leading supplier of transmission and driveline products in the aftermarket. All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• Quick Link Splice Connectors

Shift Solenoid

AT CLUTCH PLATE

ATP Automatic Transmission Control Solenoid (Lock-Up)

Cable Bracket, GM APPLICATION: For TH400, 350, 250, 200, 700R4, 2004R transmissions.

Product Features:

• Shifter Service Parts

AT OIL PUMP ORING

AUTO TRANS BAND

GM Genuine Parts Vacuum Check Valves are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

This transmission control module has been fully tested and validated to match the function and performance of the original TCM on specified vehicle applications.

Product Features:

• Direct replacement – this transmission control module matches the function and performance of the stock TCM on specified years, makes and models
• Ideal solution – this transmission control module is a reliable replacement for an original part that has failed due to corrosion or electrical failure
• Thoroughly tested – this TCM has undergone full vehicle simulator testing to confirm full functionality for reliable performance
• Requires programming – after installation, module must be programmed with original manufacturer software, such as through a Remote Assist Programming (RAP) Kit

This kit allows you to adjust the shift points of your transmission after it is installed in your vehicle. The Governor Recalibration Kit is very useful if you have a vehicle that is very light; has a low rear-end gear ratio.

Product Features:

• Adjust Shift Points Of Transmission
• Useful For Light Vehicles
• For Low Rear End Gear Ratio
• Or Useful If It Is Conversion

Product Features:

• Edelbrock Part # 8026 GM Transmission adapter is for use with 2004R, 700R4, 4L60 transmissions.
• This kit relocates the pin position on an Edelbrock Carburetor when hooking up to a throttle valve style transmission (700R4, 2004R, 4L60).
• The pin location is critical as the TV controls line pressure, shift points, shift firmness, and part throttle downshifts.

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

• Automatic Transmission Dip Stick

Detent cables connect the throttle mechanism to the transmission. Old cables can bind, break, or just become sluggish. The best repair is to replace the old cable with a new one. ATP Detent cables are designed to fit and function just like the original part to ensure durability and long life.

Product Features:

• Includes brackets, grommets, etc to match original
• Helps transmission determine ideal downshift
• Improves vehicle performance

ATP Universal Fit Detent Cables are designed to cover many applications and are no compromise replacement parts

Product Features:

• Includes brackets, grommets, etc to match original
• Fits many GM transmissions
• Adjustable

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required. All of friction components are replaced with upgraded heavy duty parts. Drum assemblies are air checked and side play is checked to assure proper clearance. All of seals, o’rings and gaskets are replaced. All of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing. Transmissions are assembled, end plays are set and fasteners are torqued to the required specification. All of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno test. Transmission park locking mechanism is checked during dyno test. (where applicable). (Torque Converter) All of converters are dynamic balanced. All of pumps are furnaced brazed. All new bearings and o’rings. All new springs and rollers in stator. All new thrust washers. All new friction liners in overdrive lockup converters. Converter endplay and hub/pump runout and diameter is checked.

Product Features:

• All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
• 100% of friction components are replaced with upgraded heavy duty parts.
• Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
• 100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear.
• Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
• Torque Converter: 100% of converters are dynamic balanced. 100% of pumps are furnaced brazed. 100% new bearings and o’rings. 100% new springs and rollers in stator. 100% new thrust washers. 100% new friction liners in overdrive lockup converters.
• 100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
• Product might not be available in all states due to local laws.

At Shift Pro Inc, fully remanufactured transmissions go beyond the name. So, what’s in that name to start? Pro Engineering: your transmission has been re-engineered to meet or exceed OE standards for tolerances, durability, and quality. Pro Performance: upgraded components and a fully remanufactured torque converter add to enhanced durability over your transmission’s lifetime. Pro Performance: hot-, cold-, load-, and simulated road-tested on custom dynamometers, your transmission is ready to go, wherever you’re headed.

Product Features:

• Fully tested torque converter included. Shift Pro Inc tests for leaks, lock-up, concentricity, and balance to eliminate the possibilities of front seal leaks, premature bushing wear, and vibration.
• All dynamometer testing is conducted with Shift Pro Inc’s custom testing program for at least 30 minutes.
• During dynamometer testing, Shift Pro Inc transmissions are cold, hot, load, and road tested using a fully synthetic transmission fluid and filtration system.
• All wear-prone valves in the completely remanufactured valve body are restored to stringent specifications and vacuum tested to verify proper function.
• Shift Pro Inc’s quality control process includes build specification checks performed by four different specialized technicians during the remanufacturing process.
• No paperwork or registration is required with Shift Pro Inc’s warranty. Each no-hassle warranty is attached to the vehicle VIN and transferrable with ownership.
• Product might not be available in all states due to local laws.

AT FRT PUMP BUSHING

This clutch pilot bushing is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this clutch pilot bushing matches the fit and function of the factory part on specified years, makes and models
• Ideal solution – this bushing is a reliable replacement for an original part that has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

AT SOLENOID SEAL

AT MODULATOR VALVE

Fully adjustable vacuum modulator to maintain accurate shift points.

Product Features:

• Meets or exceeds OE fit, form and function

B&M’s vacuum modulator is fully adjustable, this allows you to tailor your shift points to within a range of 2-4 mph. Comes preadjusted for normal shift points. For TH350 and TH400.

Product Features:

• Fully Adjustable
• Allows You To Tailor Shift Points
• Comes Supplied Pre-Adjusted

Fully adjustable vacuum modulator to maintain accurate shift points.

Product Features:

• Meets or exceeds OE fit, form and function

AT MODULATOR VALVE