Pontiac Firebird Air Intakes

Essential Pontiac Firebird Air Intakes

United Carb – Remanufactured Carburetor 2 Barrel (Part No.14-4217)

Remanufactured Carburetor 2 Barrel

from

$315.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More

Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)

Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg

from

$16.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:
  • Gasket Or Seal Included
  • 3.5 in. Hg Opening Vacuum
  • Single Stage
  • Standard Flow Type
  • Made In The USA
See More

Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1040)

Carburetor Choke Pull-Off

from

$18.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.

Product Features:
  • Application matched components ensure carburetor can be returned to like new condition.
See More

Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)

Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs

from

$284.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More

Dorman – Help – Breather Element Clips – GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9 (Part No.41113)

Breather Element Clips - GM 2002-76-Use with breather elements: AC; FB59: Fram; CA19: Purolator; AF9

from

$1.49
This air cleaner fastener is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this air cleaner fastener is designed to match the fit and function of the original part on specified vehicles
  • Ideal solution – this fastener is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)

Carburetor Accelerator Pump Diaphragm #12400 30cc

from

$12.99
Product Features:
  • The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
  • Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
See More

Mahle – FI Throttle Body Mou (Part No.C7001292101MAH)

FI Throttle Body Mou

from

$21.74
FI Throttle Body Mou

Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)

Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors

from

$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly

Product Features:
  • Multi-Color
  • Plastic Material
  • Fits Holley® 2300, 4150, And 4160 Carburetors
  • Set of 8
  • Made In The USA
See More

Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)

Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl

from

$13.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45

Product Features:
  • Fits Holley® Carburetors With Center Hung Fuel Bowl
  • Includes Adjusting Nut
  • Includes Locking Screw
  • Includes O-Ring
  • Includes Washers
See More

Felpro – Carburetor Choke Tube Gasket (Part No.72587)

Carburetor Choke Tube Gasket

from

$1.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

Dorman – Steel Cup Expansion Plug 7/8 In., Height 0.340 (sold by each) (Part No.555-014)

Steel Cup Expansion Plug 7/8 In., Height 0.340 (sold by each)

from

$1.49
This engine expansion plug is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this engine expansion plug matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this plug is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)

Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair)

from

$13.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

Product Features:
  • 57 Maximum Jet Size
  • 0.056 in. Orifice Diameter
  • 1/14-32 in. Thread Size
  • Standard Main Jet Type
  • Set of 2
See More

Edelbrock – Throttle & Auto Trans Kickdown Bracket #8030 SBC 1995 and Earlier (Non-Vortec) (Part No.8030)

Throttle & Auto Trans Kickdown Bracket #8030 SBC 1995 and Earlier (Non-Vortec)

from

$79.99


Product Features:
  • Throttle/Cruise Control/Transmission
  • Cable Mounting Bracket
See More

Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1878)

Carburetor Tune-Up Kit

from

$33.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More

Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)

Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up

from

$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent

Product Features:
  • Steel Material
  • Zinc Plated
  • Adjustable
  • 3-Barrel Configuration
  • Made In The USA
See More

Edelbrock – Intake Manifold replacement runner to base gaskets (Part No.6950)

Intake Manifold replacement runner to base gaskets

from

$33.99
Product Features:
  • For Chevy 1957-86 302-327-350-400 S/B Tunnel Ram
  • For #7110
  • Includes Hardware
  • Multi Piece Configuration
  • Set of 5
See More

Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)

Performer Carburetor Calibration Kit #1487 for #1406 Carburetors

from

$62.99
Product Features:
  • Customize Carburetor Calibration and Performance
  • Owners Manual has Assembly Help
  • Includes Metering Rod Retaining Spring
  • Includes Metering Rods
  • Includes Metering Jets
  • Includes Step-Up Springs
See More

Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)

Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors

from

$17.99
Product Features:
  • The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
  • The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
  • These will not work with accelerator pump transfer tubes.
See More

Dorman – Help – Throttle Return Spring (Part No.59209)

Throttle Return Spring

from

$9.99
This throttle return spring is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this throttle return spring matches the fit and function of the factory part on specified years, makes and models.
  • Ideal solution – this spring is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)

Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip

from

$18.99
Product Features:
  • The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
  • Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
See More

Dorman – Rivet-Push In-Hole Diameter .250 In. (Sold by each) (Part No.700-576)

Rivet-Push In-Hole Diameter .250 In. (Sold by each)

from

$0.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

Product Features:
  • Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application.
  • Quality material – this retainer is made of durable material for long-lasting service
  • Versatile design – this retainer is suitable for a variety of automotive uses
  • Excellent value – this part offers original equipment quality at a competitive cost
See More

Holley – REPLACEMENT MAIN BODY KIT FOR 0-80457S (Part No.134-342)

REPLACEMENT MAIN BODY KIT FOR 0-80457S

from

$195.99
REPLACEMENT MAIN BODY KIT FOR 0-80457S

Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)

Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415

from

$20.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to

Product Features:
  • Brass Material
  • 3/8 in. Single Barb
  • 7/8-20 in. Male End
  • 5/8-18 in. Female Flare
  • With 3/8 in. Tube
See More

Carquest Premium – Barometric Pressure Sensor Connector (Part No.PTA1166)

Barometric Pressure Sensor Connector

from

$17.79
CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:
  • Premium quality materials for longer service life
  • Sealed connections (where applicable) to prevent environmental corrosion and performance issues
  • Global coverage for import and/or domestic applications
  • OE specified wire gauge to ensure a reliable electrical connection
  • Designed to meet or exceed OE specifications in form, fit and function
See More

Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)

Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing

from

$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin

Product Features:
  • Polished Log
  • Brass Fittings
  • Black Neoprene Hose
  • 5-1/2 in. Outlet Spacing
  • Includes Hose Clamps
See More

Helping You Find the Right Air Intakes for Your Pontiac Firebird

You love your Firebird. So we’ve made it easier than ever to help you find Pontiac Firebird Air Intakes in our online catalog. Our inventory holds 299 aftermarket and OEM Air Intakes for your Pontiac Firebird, ranging from $0.99 to $1,230.00.

We offer parts from 23 brands trusted to make quality Air Intakes for your Pontiac Firebird. Before you buy, take some time to read through customer reviews. We currently have 22,061 reviews of Pontiac Firebird Air Intakes from previous customers. Some of the top rated parts include Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny with 4.7 stars and Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) with 4.6 stars.

Find your Firebird Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Pontiac Firebird part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Air Intakes Brands for Your Pontiac Firebird

Our inventory holds Air Intakes for your Pontiac Firebird from 23 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, ACDelco, and Edelbrock, all of which can keep that Pontiac happy.
We have Delphi parts available for your Pontiac Firebird in categories like Throttle Bodies & Carb Parts. Some of the top-rated Delphi parts in these categories are:
Throttle Position Sensor
from $41.49
(1)
Throttle Position Sensor
Throttle Position Sensors
Throttle Position Sensor
from $63.99
(1)
Throttle Position Sensor
Throttle Position Sensors

FAQs for Pontiac Firebird Air Intakes

What are the most purchased Air Intakes for the Pontiac Firebird?

Out of 299 Air Intakes for the Pontiac Firebird, the most popular in our inventory are:
Multi-Purpose Temperature Sensor
from $35.99
(21)
Multi-Purpose Temperature Sensor
Intake Manifold Temperature Sensors
Fuel Injector Seal Kit
from $7.79
This product is not rated
Fuel Injector Seal Kit
Carburetor and Injector Seal Kits
Engine Intake Manifold Gasket Set
from $34.99
(24)
Engine Intake Manifold Gasket Set
Intake Manifold Gasket Sets

What are the top-rated Pontiac Firebird Air Intakes?

Top-rated Air Intakes for your Pontiac Firebird based on customer reviews/ratings are: