Plymouth PB300 Performance and Racing Products

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Edelbrock part #1720 Performer RPM Series fuel pump is for Small-Block Chrysler designed for use with all Edelbrock carburetors used in Performer or Performer RPM applications. These high-performance’s street Fuel Pumps feature a high quality three stage

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

• 7 1¿4″ diameter
• 7 1┐4″ diameter
• 383 thru 440 cu. in.
• Increased Performance
• Set Valve Lash At Proper Time

The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:

• Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
• Manual Choke
• 4 Barrel Count
• Square Bore
• Smooth Secondary Transition
• Both Timed and Full Vacuum Ports
• Includes PCV Outlet

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

Product Features:

• Heavy Duty Cap and Rotor Kit
• With Brass Inserts

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features:

• Complete Pair For Hydraulic Flat Tappet
• 84cc Combustion Chamber Volume
• 210cc Intake/70cc Exhaust Runner Volume
• 2.14 in. Intake/1.81 in. Exhaust Valve Diameter
• 0.625 in. Deck Thickness

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1979 Chrysler Big Block 361-383-400-413-426-440 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

• Designed for 1958-1979 Chrysler Big Block 361-383-400-413-426-440 engines
• Baffled for breather system compatibility
• Sold in pairs
• Triple chrome-plated steel construction
• Stock height
• Features OEM style sealing edge

Oil Pan Bolt Kit

When installing headers you will need header bolts, factory exhaust manifold bolts won’t work. These Mr. Gasket Header Bolts are Grade 5 for strength, black oxide coated, and have a compact hex head that is ideal for use where space is minimal – your typical header flanges. Sold as a set of 14.

Product Features:

• 14 per Package
• Heat-Treated For Strength
• Ideal For Tight Spaces
• Grade 5 Material
• Protective Black Finish

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

• Smaller diameter CNC machined billet aluminum housing
• Must Be Used w/An MSD Ignition Control
• Supplied w/small dia. cap w/HEI style terminals; race and rotor
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate
• Mech. advance assem. can be locked out for crank trigger systems
• Advance plate and weights are fine blanked from chrome moly steel
• QPQ coated for friction reduction
• Maintenance-free magnetic pickup and precision reluctor
• Creates stable trigger signals throughout the rpm range
• Easy-to-adjust mech. advance w/supplied springs and stop bushings
• No CARB Exemption Order Number

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

• Features 12-point Smaller-than-standard Bolt Head
• Thick Flat Washers Distribute Optimum Clamp Load
• Ideal Use Where Space Is Minimal On Race Manifolds
• Bolts And Washers Zinc Plated For Protection
• Zinc Plated For Protection

2500-6500 RPM high-performance street engines. Single-plane low-rise intake good for high RPM. Ideal for applications with limited hood clearance. For top-end HP and adequate throttle response. Available in cast or polished.

Product Features:

• 2500 to 6500 RPM High Performance Street Engines
• Single-Plane Low-Rise Intake Good for High RPM
• Ideal for Applications with Limited Hood Clearance
• For Top-End HP and Adequate Throttle Response

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

• HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
• VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
• PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
• EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
• EASY TO REMOVE: Fast and easy Wrench-Off removal
• HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
• HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Header Gasket Set

Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile rubber composition gasket material
• Provides excellent sealing and durability
• Complete with molded rubber front/rear oil pan end seals where applicable
• For OE replacement, high performance street, drag race and oval track use
• Graphite Non-Wicking Rubber
• No Cork Particles
• Easy Removal For Disassembly

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1971-up Chrysler, Dodge and Plymouth 383, 400 and 440ci (externally balanced cast crankshaft) V8 engines with A727 transmission. Features include high tensile strength steel construction to resist elongation and cracking, 10.00 and 11.125 inch bolt patterns and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

• Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
• O.D.: 1.509″, I.D.: 0.697″
• Dual valve springs with damper

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
• Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
• Not intended for use in emission controlled vehicles.

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• ENGINEERED TO PERFORM — Proprietary cork-rubber formulation
• SUPERIOR SEAL — Highly conformable to accommodate for the imperfect sealing surfaces
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.