Packard Executive Parts

Packard Executive Belts and Hoses

from

$32.99

Notched V-Belt: 57.81" Long, 1 Strand, Exact Fit

from

$36.99

Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:

Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
Resists oil, heat, ozone, weather and aging for improved belt life
Meets or exceeds SAE J636C specifications

from

$20.99

Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to

Product Features:

Brass Material
3/8 in. Single Barb
7/8-20 in. Male End
5/8-18 in. Female Flare
With 3/8 in. Tube

Packard Executive Air Intakes

from

$12.99

The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var

Product Features:

Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
Includes Gasket
1/2 in. x 28 Power Valve Thread
For Applications That Prefer To Run Carbs Without The Power Valves
Made In The USA

from

$16.99

Product Features:

The Edelbrock #12645 Single Stage 4.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.

from

$16.99

The Edelbrock #12625 Single Stage 2.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:

Gasket Or Seal Included
2.5 in. Hg Opening Vacuum
Single Stage
Standard Flow Type
Made In The USA

from

$19.99

The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.

Product Features:

Nitrile Rubber Material
Metering Block Type
Set of 4
Fits Holley® 4160 Carburetors
Made In The USA

from

$14.99

Product Features:

The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
Kit includes two black nitrile fuel bowl gaskets.

from

$20.99

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

Center Hung Floats
0.11 in. Needle Diameter
Viton® Needle Material
Sold Individually
Non-Adjustable Type

from

$18.99

Product Features:

The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.

from

$13.99

The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

Product Features:

57 Maximum Jet Size
0.056 in. Orifice Diameter
1/14-32 in. Thread Size
Standard Main Jet Type
Set of 2

from

$24.99

The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.

Product Features:

Steel Material
For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
Includes Lightest To Heavy
Set of 7
Made in The USA

from

$43.99

Product Features:

The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
The kit comes with the necessary components to rebuild a 4160 style Carburetor.

from

$38.99

WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.

from

$57.99

Product Features:

The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
The kit comes with the necessary components to rebuild a 4150 style Carburetor.

from

$40.99

The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly

Product Features:

Multi-Color
Plastic Material
Fits Holley® 2300, 4150, And 4160 Carburetors
Set of 8
Made In The USA

from

$31.99

Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.

Product Features:

Rubber Material
For Holley®, Barry Grant, And Demon Gasoline Carburetors
No Hardware Included
50cc Volume
Made iIn The USA

from

$12.99

Product Features:

The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

Packard Executive Fuel and Emissions Systems

from

$64.99

Solid-state Worry Free Electronics
Internal Pressure Regulating
Universal Design Allows For Easy Installation
No DiaphraGMs Or Mechanical Parts To Wear Out
They Make An Excellent Fuel Transfer or Booster Pump
Not designed for use on aircraft of any type.
Hose Barbs Fit 5/16″ Fuel Hose
Self-priming, 2 wire design
Eliminates vapor lock and flooding

from

$56.99

Gravity fed type pump with simple two-wire design. Works on 12 Volt negative ground systems only. Includes fittings and mounting hardware along with easy to follow DIY instructions. Pumps require approximately one amp average draw at maximum delivery. Flow rate is 28 gallons per hour (GPH) at 2 to 3-1/2 pounds per square inch (PSI). Universal design for most import 4 & 6-cylinder carburetor applications. Please see part #12S for V8 gasoline applications, part #12D for diesel applications or part #12E for Ethanol, Methanol, E85 and Race Fuel applications. Solid-state worry free electronics. Eliminates vapor lock and flooding. Works well as a fuel transfer, booster, or stand-alone pump. Not recommended for diesel, methanol, ethanol, E85 or race fuel applications!!

Product Features:

Solid-state Worry Free Electronics
Internal Pressure Regulating
Universal Design Allows For Easy Installation
No DiaphraGMs Or Mechanical Parts To Wear Out
Makes An Excellent Fuel Transfer or Booster Pump
Hose Barbs Fit 5/16″ Fuel Hose
Self-priming, 2 wire design
Eliminates vapor lock and flooding

Packard Executive Steering and Chassis Parts

from

$384.99

Power Steering Pumps are thoroughly cleaned and exterior surfaces reconditioned for like-new look. Each component is carefully inspected and replaced if not to OE tolerances. All seals and O-rings are replaced with OE equivalent parts. Each unit is tested to insure OE performance. Painted with a high quality paint. All units are carefully packaged to insure safe arrival at your door. Remanufactured in the USA.

from

$154.99

Rare Parts prides itself in only manufacturing high quality chassis parts. Diamond Series parts will exceed OEM and aftermarket products. Examples would be: forged verses stamped housings, greaseable, tighter machining tolerances, and proper heat treat of ball studs and mating components. Every Diamond Series part is tested and inspected in our facility prior to being sold. So rest assured you are getting a quality part when quality counts.

Product Features:

Increased forging size
Precision machining tolerances
Heat treated components
Low friction

Packard Executive Suspension Parts

from

$103.99

This high quality chassis part will improve overall vehicle handling, reduce tire wear and increase the life of other steering and suspension components. These chassis parts are manufactured to meet or exceed OEM.

Product Features:

Reduces vibration
Torsional rubber bushings
UV resistant
No Squeak

from

$13.29

Monroe® Shock-Mate® Shock Absorber Boot Kits are universal replacement shock boots use to protect the shock’s piston rod from dirt, mud and other contaminants – protecting the life of your shocks.

Product Features:

Protects the shock’s piston rod from damage
Universal design for easy installation
Tie-strap included for a secure fit
Constructed from high quality urethane for maximum durability
Multiple color choices available

from

$17.49

Rubber or Heat Treated bushings
No Squeak
Reduces vibration

from

$21.79

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

Easy to install
Restores like-new steering and handling
Engineered to provide long life and dependability
Construction and design validated by MOOG engineers
Incorporates proven design and engineering features

from

$4.99

Rubber or Heat Treated bushings
No Squeak
Reduces vibration

from

$27.99

Gas-charged shock absorber that provides improved vehicle control for today’s light trucks, vans, full-size picks-ups and 4×4’s at an economical price.

Product Features:

Available for import and domestic trucks, vans, full-size pick-ups and 4×4’s
Gas-charged unit
Improved handling and control
Economical OE replacement
Meets OE product specifications

from

$44.49

Designed to restore a vehicle’s original factory drivability and performance, Monroe® OESpectrum® passenger car shock absorbers provide an exceptional level of handling precision and control while filtering out noise, vibration and harshness.

Product Features:

REDUCED NOISE, VIBRATION AND HARSHNESS — Twin Technology Active Control System delivers exceptional control under most driving conditions while isolating impact-related noise, vibration and harshness
EXCEPTIONAL HANDLING — Full displaced valving, tuned specifically to each vehicle, adjusts to road extremes while the larger bore provides more efficient damping control to provide consistency and a smooth ride
CONTROL AND DURABILITY — Fluon-banded piston provides consistent sealing between piston and pressure tube for better control and increased durability
CONSISTENT RIDE — OE all-weather fluid contains special additives to assist with extreme temperatures and help reduce oil breakdown
IMPROVES PERFORMANCE — Nitrogen gas-charge maintains tire-to-road contact for improved ride and handling by reducing aeration and shock fade
Nitrogen Gas Charged: For improved ride and handling, helps maintain tire to road contact by reducing aeration – on most applications
1/2 inch Diameter Piston Rod: Nitrocarburized rod for long service life. On non-dust shield units only.
Special Seal: ‘Self-lubricating’ fluid seal designed to retain gas without excessive wear or friction.

from

$13.99

Protects the shock’s piston rod from damage
Universal design for easy installation
Tie-strap included for a secure fit
Constructed from high quality urethane for maximum durability
Multiple color choices available

Looking for the best Packard Executive aftermarket replacement parts? Replacing worn and broken parts on your Packard Executive? Check out our online catalog to find the best selection of aftermarket Packard Executive parts as well as real user reviews on Packard Executive replacement parts. Make an informed decision about every component you add to your Executive.

At Advance Auto, we’ve got you covered when it comes to getting your Packard Executive in tip top condition. We’ve got over 93 Packard Executive parts to choose from in popular categories like Belts and Hoses, Air Intakes and Fuel and Emissions Systems. If you’re looking for the best prices, try searching our Packard Executive parts catalog to compare OEM and aftermarket parts for your Packard Executive.

Whether you need Packard Executive body parts, interior components, or custom Packard Executive parts you can find them online at Advance Auto. Want to order your Steering and Chassis Parts online? Or maybe you need your Packard Suspension Parts same day? No problem, you can pick up Executive parts in person at locations across the country, or have them delivered to straight to your door after ordering online. Finding a great deal on new and used Packard Executive parts has never been easier.

Advance Auto customers frequently search for the following types of Packard Executive auto parts. Check out customer reviews and ratings, and compare prices on the following Packard Executive parts:

People also search Advance Auto for these popular years of the Packard Executive:

Packard Executive Parts

Gates – Notched V-Belt: 57.81" Long, 1 Strand, Exact Fit (Part No.7570)

Gates – Automotive XL« High Capacity V-Belt (Part No.9550)

Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)

Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)

Edelbrock – Standard Flow Carburetor Power Valve #12645 Single Stage 4.5in Hg (Part No.12645)

Edelbrock – Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg (Part No.12625)

Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)

Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)

Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)

Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)

Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)

Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)

Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)

Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1785)

Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)

Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)

Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)

Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)

Mr. Gasket – Electric Fuel Pump (Part No.12S)

Mr. Gasket – High Performance Electric Fuel Pump – Universal Carbureted Engines (Part No.42S)

Lares – Remanufactured Power Steering Pump (Part No.2083)

Rare Parts – Idler Arm (Part No.RP20379)

Rare Parts – Control Arm Bushing (Part No.RP17280)

Monroe – Shock-Mate Shock Absorber Boot Kit (Part No.SA1998)

Rare Parts – Leaf Spring Bushing (Part No.RP36068)

MOOG – Leaf Spring Bushing (Part No.K7308)

Rare Parts – Spring Bushing (Part No.RP35499)

Monroe – Gas-Matic LT Shock Absorber (Part No.59347)

Monroe – OESpectrum Passenger Car Shock Absorber (Part No.5751)

Monroe – Shock-Mate Shock Absorber Boot Kit (Part No.SA1997)