Packard Clipper Carburetor Parts

Product Features:

• The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
• Kit includes two black nitrile fuel bowl gaskets.

The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45

Product Features:

• Fits Holley® Carburetors With Center Hung Fuel Bowl
• Includes Adjusting Nut
• Includes Locking Screw
• Includes O-Ring
• Includes Washers

The Edelbrock No. 12685 Single Stage 8.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.

The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:

• Gasket Or Seal Included
• 3.5 in. Hg Opening Vacuum
• Single Stage
• Standard Flow Type
• Made In The USA

The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var

Product Features:

• Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
• Includes Gasket
• 1/2 in. x 28 Power Valve Thread
• For Applications That Prefer To Run Carbs Without The Power Valves
• Made In The USA

The Edelbrock 94 No. 12474 Carburetor Jets .074″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12470 Carburetor Jets .070″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Edelbrock 94 No. 12481 Carburetor Jets .081″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a

Product Features:

• Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
• Performance Upgrade For Stock To Mildly Modified Vehicles
• Universal Calibration For Easy Bolt-On Performance
• Man. Choke Cable Hand Controlled For Cold Start Control
• Vacuum Secondaries For Use On Wide Variety Of Vehicles
• Single Feed Fuel Inlet For Easy Installation

Holley engineers have taken the state-of-the-art Gen 3 Ultra carburetors and created a budget friendly version that is perfect for street/strip applications as well as all out bracket or sportsman drag cars. The new Holley SP Dominator carburetors feature the patent pending Gen 3 main-body which is 5/16″ taller than the previous generation! This new height allowed for larger radius air entries to deliver smoother flow that equates to improved throttle response and consistency. An extended air cleaner flange is incorporated for easy air scoop attachment when using the available air scoop adapter. Other features include all aluminum construction, tunable billet metering blocks, throttle position sensor mounting points and knurled (hand adjustable) curb idle screws. Each calibration has been dyno and track tested to deliver proven performance!

Product Features:

• All Aluminum Construction Saves 3.8 lbs. Over Original Models
• 28% Weight Savings
• Shiny With Billet Aluminum Metering Block and Black Hardware
• Calibrations Optimized For Todays Race Engines and New Fuels
• Fully Machined From Venturi Throat To Throttle Bore For Perf
• Annular Booster Deliver Excellent Signal and Throttle Response
• Screw In Air Bleeds Offer Precise Tuning Capabilities
• Metering Blocks Feature Improved True Gasket Sealing
• Dual 50CC Accelerator Pumps Fuel From Idle To Full Throttle
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• Clear Sight Windows On Fuel Inlet Side For Fuel Level Adjustment
• Notched Float and Jet Extension Are Factory Installed

The Ultra Street Avenger carburetors feature all aluminum construction and are equipped with metering blocks and a base plate made from 6061-T6 billet aluminum. They weigh in at approximately 5 lbs less than a comparable zinc carburetor. The new Ultra Street Avenger carburetors have the same great features as their aluminum counterparts such as a tumble polished aluminum finish; quick change vacuum secondaries for easy tuning to optimize performance or fuel economy; four vacuum ports for all necessary vacuum accessories; factory preset electric choke for easy startups; built-in fuel filters; and an included fuel line kit so there are no unnecessary trips back to the parts store. Ultra Street Avengers feature the same optimized street calibration as the zinc versions so you know they will run great on your vehicle. In addition, the Ultra Street Avenger now comes with anodized metering blocks and a base plate made from 6061-T6 billet aluminum and a built in, clear fuel level sight glass for easy, no mess fuel level adjustments. Don’t trust your performance to just anyone, Holley is the only Modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:

• Ultra Street Avenger Has Optimized Calibration Works Out Of Box
• Factory Preset Electric Choke For Easy Startups
• Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
• 4 Corner Idle Allows You To Precisely Control Your Idle System
• Built In Clear Fuel Level Sight Glass For Fuel Level Adjustment
• Aluminum Construction For A 43% Weight Savings
• No Unnecessary Trips Back To The Parts Store
• Limited Lifetime Warranty
• 100% Wet Flow Tested By Holley Technicians
• Arrives Ready To Run

The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:

• Center Hung Floats
• 0.11 in. Needle Diameter
• Viton® Needle Material
• Sold Individually
• Non-Adjustable Type

Product Features:

• The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
• Improper installation will void your warranty and may result in poor performance and engine or vehicle damage

Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.

Product Features:

• Rubber Material
• For Holley®, Barry Grant, And Demon Gasoline Carburetors
• No Hardware Included
• 50cc Volume
• Made iIn The USA