Packard Clipper Air Intakes
Top Packard Clipper Air Intakes Categories
We carry over 96 Air Intakes in inventory for the Packard Clipper. If you’re looking for aftermarket Air Intakes for your Packard Clipper, check out all these categories:
Essential Packard Clipper Air Intakes
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors (Part No.12750)
from
$47.99
Product Features:
See More
- The Edelbrock #12750 4160 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4160 style Carburetor.
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1785)
from
$38.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12371 Fits 4160 Carburetors (Part No.12371)
from
$20.99
The Edelbrock #12371 kit includes the primary fuel bowl gasket, the primary metering block gasket, the secondary metering block gasket and a metering plate gasket. The Edelbrock #12371 fits Holley 4160 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block Type
- Set of 4
- Fits Holley® 4160 Carburetors
- Made In The USA
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 9001 SH-1)
from
$26.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Validated for fit, form, and function
- Includes all parts needed to complete the repair
- Includes all parts needed to complete the repair
Holley – Street Carbs (Part No.0-3310S)
from
$531.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibratory Polished Alum Good Looks/Weight Savings/Lasting Shine
- Performance Upgrade For Stock To Mildly Modified Vehicles
- Universal Calibration For Easy Bolt-On Performance
- Man. Choke Cable Hand Controlled For Cold Start Control
- Vacuum Secondaries For Use On Wide Variety Of Vehicles
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
Holley – Performance and Race Carburetor: 850 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-76850BL)
from
$949.99
Holley Double Pumper(R) carburetors are a perfect performance upgrade for hot street cars and race vehicles. Double Pumper carburetors are an American icon when it comes to performance carburetors. From their roots as the premier carburetor on many factory muscle cars to powering thousands of vehicles across the finish line, the Double Pumper is a great choice whether you are burning up the street or the quarter mile.
Product Features:
See More
Product Features:
- Metering Blocks Base Plate For Good Looks True Gasket Sealing
- Optimized Street/Strip Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Mechanical Secondaries For Awesome Tire Turning Performance
- 4 Corner Idle Allows You To Precisely Control Your Idle System
- Clear Fuel Level Sight Glass No Mess Fuel Level Adjustments
- Aluminum Construction For A 43% Weight Savings
- Lightweight Vehicles w/Auto Trans w/High Stall/Low Gearing
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Edelbrock – Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors (Part No.12382)
from
$16.99
Product Features:
See More
- The Edelbrock #12382 fuel bowl gasket is designed for Holley 2300, 4150, 4160, 4175 and 4500 Carburetors.
- Kit includes two black nitrile fuel bowl gaskets.
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Packard Clipper Air Intakes Categories
Helping You Find the Right Air Intakes for Your Packard Clipper
You love your Clipper. So we’ve made it easier than ever to help you find Packard Clipper Air Intakes in our online catalog. Our inventory holds 96 aftermarket and OEM Air Intakes for your Packard Clipper, ranging from $13.99 to $1,949.99.
We offer parts from 4 brands trusted to make quality Air Intakes for your Packard Clipper. Before you buy, take some time to read through customer reviews. We currently have 181 reviews of Packard Clipper Air Intakes from previous customers. Some of the top rated parts include Street Carbs with 4.0 stars and Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet with 5.0 stars.
Find your Clipper Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Packard Clipper part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Packard Clipper
Our inventory holds Air Intakes for your Packard Clipper from 4 trusted brands. You’ll find OEM and aftermarket parts from brands like Edelbrock, Holley, and FELPRO, all of which can keep that Packard happy.
We have Edelbrock parts available for your Packard Clipper in categories like Carburetor Parts. Some of the top-rated Edelbrock parts in these categories are:
from
$18.99
(1)
Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors
Carburetor and Injector Mount Gaskets
from
$13.99
(1)
Carburetor Accelerator Pump Diaphragm #12400 30cc
Carburetor Accelerator Pump Diaphragms
from
$16.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
Carburetor and Injector Mount Gaskets
Top-Rated Holley Air Intakes
Leading Holley Air Intakes
We carry Holley brand parts for your Packard Clipper across several catalog categories, including Carburetor Parts. Some of our most reviewed Holley parts include:
from
$599.99
(2)
Street Carburetor: 450 CFM, No Choke, 4 Barrel, Square Bore, Single Inlet, Gold Dichromate
Carburetors
FAQs for Packard Clipper Air Intakes
What are the most purchased Air Intakes for the Packard Clipper?
Out of 96 Air Intakes for the Packard Clipper, the most popular in our inventory are:
from
$47.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
from
$60.99
This product is not rated
Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated Packard Clipper Air Intakes?
Top-rated Air Intakes for your Packard Clipper based on customer reviews/ratings are:
from
$849.99
(2)
Street Carbs
“As you would expect from Holley this is a great carb for my 6 cyl Jeep.”
from
$799.99
(1)
Performance and Race Carburetor: 600 CFM, Manual Choke, 4 Barrel, Square Bore, Dual Inlet
“Great price on a performance carb. Will be used on a “restored” project. Holley is aLways a good choice”
