Oldsmobile Cutlass Supreme Air Intakes

Essential Oldsmobile Cutlass Supreme Air Intakes

Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)

Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair)

from

$14.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.

Product Features:
  • 57 Maximum Jet Size
  • 0.056 in. Orifice Diameter
  • 1/14-32 in. Thread Size
  • Standard Main Jet Type
  • Set of 2
See More

Holley – Street Carbs (Part No.0-3310C)

Street Carbs

from

$631.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.

Product Features:
  • Gold Dichromate Finish For Corrosion Resistance w/Classic Look
  • Performance Upgrade For Stock To Mildly Modified Vehicles
  • Universal calibration for easy bolt-on performance
  • Man. Choke Cable Hand Controlled For Cold Start Control
  • Vacuum Secondaries For Use On Wide Variety Of Vehicles
  • Dual feed fuel inlets for constant high volume fuel delivery
  • Power Valve Blow Out Protection
  • 100% Wet Flow Tested By Holley Technicians
  • Arrives Ready To Run
See More

Carquest – Carburetor Choke Thermostat (Part No.779-1485)

Carburetor Choke Thermostat

from

$69.05
Carquest distributes a full line of engine management products, providing the aftermarket with premium quality and comprehensive coverage.
See More

Dorman – Help – Air Cleaner Wing Nut – 1/4 In. (Part No.41200)

Air Cleaner Wing Nut - 1/4 In.

from

$7.99
This air cleaner fastener is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:
  • Direct replacement – this air cleaner fastener is designed to match the fit and function of the original part on specified vehicles
  • Ideal solution – this fastener is a reliable replacement for an original part that is missing or has failed due to fatigue
  • Durable construction – this part is made from quality materials to ensure reliable performance and long service life
  • Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
See More

Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1744)

Carburetor Repair Kit

from

$28.99
Product Features:
  • Application matched component to ensure the system can be returned to like new condition.
  • Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
See More

Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)

Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up

from

$196.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent

Product Features:
  • Steel Material
  • Zinc Plated
  • Adjustable
  • 3-Barrel Configuration
  • Made In The USA
See More

Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)

Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415

from

$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to

Product Features:
  • Brass Material
  • 3/8 in. Single Barb
  • 7/8-20 in. Male End
  • 5/8-18 in. Female Flare
  • With 3/8 in. Tube
See More

Dorman – Rivet-Push In-Hole Diameter .250 In. (Part No.799-110)

Rivet-Push In-Hole Diameter .250 In.

from

$5.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

Product Features:
  • Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
  • Quality material – this retainer is made of durable material for long-lasting service
  • Versatile design – this retainer is suitable for a variety of automotive uses
  • Excellent value – this part offers original equipment quality at a competitive cost
See More

Felpro – Air Cleaner Mounting Gasket (Part No.60038)

Air Cleaner Mounting Gasket

from

$4.29
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Engineered for the sealing repair environment
  • Unsurpassed quality you can trust
  • Validated for fit, form, and function
See More

Edelbrock – Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg (Part No.12635)

Standard Flow Carburetor Power Valve #12635 Single Stage 3.5in Hg

from

$17.99
The Edelbrock #12635 Single Stage 3.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate. During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation

Product Features:
  • Gasket Or Seal Included
  • 3.5 in. Hg Opening Vacuum
  • Single Stage
  • Standard Flow Type
  • Made In The USA
See More

Felpro – Carburetor Heat Shield Gasket (Part No.60731)

Carburetor Heat Shield Gasket

from

$7.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Unsurpassed quality you can trust
  • Validated for fit, form and function
  • Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
See More

Edelbrock – Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs (Part No.2040)

Chevrolet SB Performer EPS Manifold w/ Gaskets, Bolts, Studs

from

$299.99
Edelbrock part #2040 Manifold Installation kit will simplify the process of adding more power and efficiency to your street rod or muscle car. It combines all the necessary components to replace your stock iron intake manifold with an Edelbrock aluminum i
See More

Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)

Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs

from

$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.

Product Features:
  • Steel Material
  • For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
  • Includes Lightest To Heavy
  • Set of 7
  • Made in The USA
See More

Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)

Rubber Expansion Plug 1-5/8 In. - Size Range 1-5/8 In. - 1-3/4 In.

from

$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.

Product Features:
  • Manufactured from high quality materials for a long service life
  • Torque values listed on parts (where applicable)
  • Easy to install
  • Constructed to strict engineering quality standards
See More

Carquest Premium – Air Charge Temperature Sensor (Part No.WTA1078)

Air Charge Temperature Sensor

from

$36.99
The temperature of various systems must be reported to the engine control module (ECM) as well as other operating system controllers in the vehicle. Coolant temperature, cabin temperature, exhaust temperature and ambient temperature are just a few systems reported by a temperature sensor. The temperature sensor is fed 5 volts by the systems computer, within the sensor housing will be a thermistor, or dropping resistor whose resistance value will change as the temperature surrounding it changes. Changing resistance in the circuit will change the volt signal at the processor indicating the current operating value.

Product Features:
  • Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
  • 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
  • 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
  • Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
  • Lead frame terminal size and location determined using image dimension measuring system or 3D laser scanner.
  • Application matched components ensures system operation in like new condition.
See More

Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)

Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors

from

$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly

Product Features:
  • Multi-Color
  • Plastic Material
  • Fits Holley® 2300, 4150, And 4160 Carburetors
  • Set of 8
  • Made In The USA
See More

Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)

Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip

from

$22.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23

Product Features:
  • Center Hung Floats
  • 0.11 in. Needle Diameter
  • Viton® Needle Material
  • Sold Individually
  • Non-Adjustable Type
See More

Carquest Premium – Multi-Use Connector (Part No.PTA1166)

Multi-Use Connector

from

$20.99
Modern vehicles may have 100 or more electrical harness connectors in every operating system of the vehicle. Terminal tension may weaken with time or corrosion may occur within the connector housing making replacement necessary. When replacing any harness-connector assembly approved wire termination methods must be followed to ensure a successful and long-term solution to the original problem is made. A failed terminal connection, terminal corrosion or damaged wire will result in an electrical system fault.

Product Features:
  • Carquest electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
  • WVE electrical connectors meet or exceed OE wire gauge, insulation, and terminal material requirements.
  • Product constructed to meet all design and operating characteristics as intended by the manufacturer.
  • OE specified wire gauge to ensure a reliable electrical connection
  • Designed to meet or exceed OE specifications in form, fit and function
See More

Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)

Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors

from

$18.99
Product Features:
  • The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
  • The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
  • These will not work with accelerator pump transfer tubes.
See More

Edelbrock – Performer EPS Intake Manifold for 1955-86 Small-Block Chevy, Polished Finish (Part No.27011)

Performer EPS Intake Manifold for 1955-86 Small-Block Chevy, Polished Finish

from

$530.99


Product Features:
  • Polished Version Of Edelbrock PN[2701]
  • Polish is Hand-Buffed for Brilliant Shine
  • Maximizes Performance with Edelbrock Carburetors
  • Maximizes Peak Torque Around 3500 RPM
  • Excellent Throttle Response and Mid-Range Power
  • Prod. +5 HP and +9 ft/lbs. of Torque Over PN[2101]
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
See More

Dorman – GM Panel Retainer (Part No.963-021D)

GM Panel Retainer

from

$4.99
Constructed of quality materials, this multi-purpose retainer provides the same function and versatility as the original equipment retainer ensuring long service life.

Product Features:
  • Ideal replacement – this retainer matches the fit and function of the original equipment retainer for this vehicle application
  • Quality material – this retainer is made of durable material for long-lasting service
  • Versatile design – this retainer is suitable for a variety of automotive uses
  • Excellent value – this part offers original equipment quality at a competitive cost
See More

Carquest Premium – Throttle Position Sensor (Part No.ECC1245)

Throttle Position Sensor

from

$103.99
Carquest Throttle Position Sensors offer precision signaling to the ECM to ensure optimum performance and fuel economy. Manufactured using the highest quality OEM approved materials, resulting in tighter tolerances and increased durability. All Carquest Throttle Position Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:
  • Manufactured to provide superior sealing, protecting against all engine bay contaminants and insulation from extreme hot and cold temperatures.
  • 100% calibrated and end-of-line tested to ensure worry-free, out-of-the-box performance
  • Designed to meet or exceed all OEM specifications in fit, form & function
  • Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.
See More

Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1044)

Carburetor Choke Pull-Off

from

$39.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.

Product Features:
  • Application matched components ensure carburetor can be returned to like new condition.
See More

Carquest Premium – Multi-Purpose Relay (Part No.RAA1266)

Multi-Purpose Relay

from

$20.99
Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

Product Features:
  • Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
  • Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
  • Where applicable, robust circuit board design increases durability due to heat, shock, and random electro-magnetic pulses (EMP) and power spikes.
  • Tin plated lead frame prevents corrosion and ensures a reliable terminal connection under adverse ambient conditions.
  • 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
  • 100% end-of-line tested to ensure accurate signal output providing product reliability, every time.
See More

Helping You Find the Right Air Intakes for Your Oldsmobile Cutlass Supreme

You love your Cutlass Supreme. So we’ve made it easier than ever to help you find Oldsmobile Cutlass Supreme Air Intakes in our online catalog. Our inventory holds 238 aftermarket and OEM Air Intakes for your Oldsmobile Cutlass Supreme, ranging from $1.99 to $1,949.99.

We offer parts from 15 brands trusted to make quality Air Intakes for your Oldsmobile Cutlass Supreme. Before you buy, take some time to read through customer reviews. We currently have 16,609 reviews of Oldsmobile Cutlass Supreme Air Intakes from previous customers. Some of the top rated parts include Engine Intake Manifold Gasket Set with 4.6 stars and Ultra-Seal Intake Manifold Gasket with Silicone Beading with 4.3 stars.

Find your Cutlass Supreme Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Oldsmobile Cutlass Supreme part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Air Intakes Brands for Your Oldsmobile Cutlass Supreme

Our inventory holds Air Intakes for your Oldsmobile Cutlass Supreme from 15 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Mr. Gasket, all of which can keep that Oldsmobile happy.
We have Delphi parts available for your Oldsmobile Cutlass Supreme in categories like Throttle Bodies & Carb Parts. Some of the top-rated Delphi parts in these categories are:
Throttle Position Sensor
from $50.99
(1)
Throttle Position Sensor
Throttle Position Sensors
Throttle Position Sensor
from $73.99
(1)
Throttle Position Sensor
Throttle Position Sensors

Top-Rated Edelbrock Air Intakes

Leading Edelbrock Air Intakes

We carry Edelbrock brand parts for your Oldsmobile Cutlass Supreme across several catalog categories, including Carburetor Parts and Air Cleaner Parts. Some of our most reviewed Edelbrock parts include:

FAQs for Oldsmobile Cutlass Supreme Air Intakes

What are the most purchased Air Intakes for the Oldsmobile Cutlass Supreme?

Out of 238 Air Intakes for the Oldsmobile Cutlass Supreme, the most popular in our inventory are:
Engine Intake Manifold Gasket Set
from $30.99
(46)
Engine Intake Manifold Gasket Set
Intake Manifold Gasket Sets
Air Cleaner Mounting Gasket
from $4.29
(39)
Air Cleaner Mounting Gasket
Air Cleaner Mount Gaskets
Throttle Position Sensor
from $46.99
This product is not rated
Throttle Position Sensor
Throttle Position Sensors

What are the top-rated Oldsmobile Cutlass Supreme Air Intakes?

Top-rated Air Intakes for your Oldsmobile Cutlass Supreme based on customer reviews/ratings are:
Engine Intake Manifold Gasket Set
from $104.99
(25)
Engine Intake Manifold Gasket Set
“Al the parts needed to get the job done”
Ultra-Seal Intake Manifold Gasket with Silicone Beading
from $34.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
“Can’t go wrong with Mr Gasket”
Intake Manifold Bolts
from $17.99
(12)
Intake Manifold Bolts
“Product is very reasonable in price and works great”