Nissan 240SX Towing Products

Many of today’s tow vehicles are equipped with separate brake lights and turn signals, however, the trailers we tow still use the combined taillight for brake and turn. The 48915 taillight converter is designed to combine the independent vehicle brake light and turn signal and combine them for the common-bulb trailer lights. Includes a built-in 4 flat connector.

Product Features:

• 60 in. Long
• Adapts Tow Vehicles Taillight System To The Trailers
• Powers Up To 2.1 Amps Per Output
• Double-Molded Weatherproof Design; Includes Dust Cover
• Corrosion Resistant Terminals
• Includes Splices And Terminal Grease
• Complete With Splices And Circuit Tester

Many of today’s vehicles do not possess the electrical means for powering the extra voltage requirements of a trailer. Power Taillight Converters units completely isolate the tow vehicle from trailer malfunctions. Power is taken directly from the battery

Product Features:

• For Vehicles w/Independent Bulb Turn Signals/Common Bulb System
• Protects Tow Vehicle Electronics And Itself From Wiring Shorts
• Self-Resetting
• Includes 12 Ga. Power Lead Wire
• Includes Fuse/Fuse Assembly/Splices/Cable Ties
• Powers Up To 8.0 Amps Per Output
• Receives Power Directly From The Battery
• Includes Vehicle Side 4 Flat
• Includes Dust Cover And Grease Packet To Prevent Corrosion

The 46155 Universal Taillight Converter Kit has everything needed to make a vehicle equipped with independent turn signals tow ready. By including splice connectors and a circuit probe tester, this kit includes the extra tools required to complete the project.

Product Features:

• 60 inch length
• Electronic Taillight Converter adapts tow vehicles taillight system to the trailer’s
• Double-molded weatherproof design
• Includes L.E.D. circuit tester, 3 splice connectors, cable ties, dust cover, ground screw, and grease packet
• Includes 4 wire flat extension
• Includes vehicle side 4 flat
• Includes dust cover and grease packet to prevent corrosion
• Includes Dust Cover And Grease Packet To Prevent Corrosion

Many of today’s vehicles do not possess the electrical means for powering the extra voltage requirements of a trailer. Power Taillight Converters units completely isolate the tow vehicle from trailer malfunctions. Power is taken directly from the battery for isolation and brighter trailer tail lights.

Product Features:

• For vehicles equipped with independent bulb turn signals or common bulb systems
• Protects tow vehicle electronics from wiring shorts
• Includes 14 ga. power lead wire, fuse & fuse assembly, splices, and cable ties
• Powers up to 5.0 amps per output
• Receives power directly from the battery
• Includes vehicle side 4 flat
• Includes dust cover and grease packet to prevent corrosion
• Includes Dust Cover And Grease Packet To Prevent Corrosion

CURT class 1 trailer hitches are the lightest-duty hitches of our rear mount lineup. They are engineered for reliability, welded together with quality steel and blasted clean for a smooth finish. Tested to meet the strict demands of the industry, this CURT class 1 hitch has a capacity to tow up to 1,500 lbs. of gross trailer weight and 150 lbs. of tongue weight. This means it can handle a variety of small trailers such as single-axle utility trailers, canoe and kayak trailers, dirt bike trailers and more (NOTE: Never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc.). This class 1 hitch is a fixed-tongue hitch, having a fixed draw bar to accept a trailer ball rather than a receiver tube to accept a ball mount. Class 1 hitches are typically mounted on compact cars, full-size cars and some smaller crossover SUVs, minivans and compact SUVs. This particular hitch is designed to be a custom-fit trailer hitch for certain years of the Nissan 240SX coupe or Nissan 240SX convertible (to verify your vehicle compatibility, see the CURT application guide at curtmfg.com). It comes with all necessary installation hardware. Each CURT class 1 hitch is co-cured with a liquid A-coat and a high-gloss black powder coat that provide a lasting defense against rust, wear and harmful UV rays.

Product Features:

• Rated to 1,500 lbs. gross trailer weight and 150 lbs. tongue weight
• Engineered with a vehicle-specific design for a custom fit
• Concealed main body for OE look and seamless integration with the vehicle
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Fixed drawbar readily accepts a 3/4″ trailer ball shank
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid A-coat, inside and out
• Made in USA (may include imported hardware)

CURT class 1 trailer hitches are the lightest-duty hitches of our rear mount lineup. They are engineered for reliability, welded together with quality steel and blasted clean for a smooth finish. Tested to meet the strict demands of the industry, this CURT class 1 hitch has a capacity to tow up to 1,500 lbs. of gross trailer weight and 150 lbs. of tongue weight. This means it can handle a variety of small trailers such as single-axle utility trailers, canoe and kayak trailers, dirt bike trailers and more (NOTE: Never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc.). This class 1 hitch is a fixed-tongue hitch, having a fixed draw bar to accept a trailer ball rather than a receiver tube to accept a ball mount. Class 1 hitches are typically mounted on compact cars, full-size cars and some smaller crossover SUVs, minivans and compact SUVs. This particular hitch is designed to be a custom-fit trailer hitch for certain years of the Nissan 240SX Fastback (to verify your vehicle compatibility, see the CURT application guide at curtmfg.com). It comes with all necessary installation hardware. Each CURT class 1 hitch is co-cured with a liquid Bonderite coating and a high-gloss black powder coat that provide a lasting defense against rust, wear and harmful UV rays.

Product Features:

• Rated to 1,500 lbs. gross trailer weight and 150 lbs. tongue weight
• Engineered with a vehicle-specific design for a custom fit
• Concealed main body for OE look and seamless integration with the vehicle
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Fixed drawbar readily accepts a 3/4″ trailer ball shank
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid Bonderite coating
• Made in USA (may include imported hardware)

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Connect to your lifestyle with a custom hitch receiver from CURT. All of our custom hitches are designed for a vehicle-specific fit, manufactured with pride, finished for industry-leading rust resistance and tested to rigorous SAE J684 standards for safety. This class 1 trailer hitch and ball mount combination is designed for a custom fit on select years of the Nissan 240SX (see application info to verify fitment). The hitch integrates with the vehicle’s frame and provides a useful and dependable 1-1/4″ x 1-1/4″ receiver. The receiver is perfect for attaching the included ball mount and towing a small trailer, or for adding cargo space with a hitch-mounted cargo carrier, bike rack or other accessory. This particular class 1 hitch is rated for 2,000 pounds gross trailer weight and 200 pounds tongue weight (never exceed the lowest-rated towing component). The ball mount included with this trailer hitch quickly and easily installs into the hitch receiver and has a 3/4″ trailer ball hole (trailer ball not included). It can be mounted in the rise or drop position to promote level towing. Like all CURT custom hitches, this class 1 hitch is protected with our co-cured finishing process. It is descaled for a smooth surface, immersed in liquid Bonderite for rust resistance inside and out, covered with a durable black powder coat and finally co-cured for an industry-leading rust, chip and UV-resistant shield. No matter where you’re headed or which season of the year you’re towing in, this CURT hitch is equipped for long-lasting resilience to the elements. It features an open-back receiver for easy cleaning, and it comes with all the hardware necessary for the installation.

Product Features:

• Rated to 2,000 lbs. gross trailer weight and 200 lbs. tongue weight
• Engineered with a vehicle-specific design for a custom fit
• Concealed main body for OE look and seamless integration with the vehicle
• Tested for safety in accordance with SAE J684
• Precisely welded for superior strength and fit
• Protected by a durable high-gloss black powder coat finish
• Co-cured in a rust-resistant liquid Bonderite coating
• Equipped with an open-back receiver for easy cleaning
• 1-1/4″ x 1-1/4″ ball mount features a 3/4″ hole to accept a trailer ball shank
• Ball mount can be flipped to provide drop or rise for level towing
• Made in USA (may include imported hardware)