Mitsubishi Cordia Alternators and Starters

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The starter motor is responsible for rotating the engine during the starting process. The electric starter motor has several serviceable parts making repair economical when single part replacement will suffice.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• Application matched component to ensure the system can be returned to like new condition.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Product Features:

• Brand may vary by location

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

Product Features:
• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Carquest Premium starters are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium starters are designed to meet or exceed OE specifications for fit, form and function. Our starters are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and needle bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Remanufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• 100% remanufactured drive clutch assembly ensures lasting performance
• Armatures and commutators are 100% load tested
• New motor lead terminals and solenoid contacts are used to ensure maximum connectivity
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-9672

Product Features:

• Engineered to meet or exceed OEM specifications for a perfect fit and hassle-free installation.
• Premium grade solenoids contains materials specifically selected for best conductivity. High temperature cap ensures that the solenoid works flawlessly in high heat environments. High dielectric strength outer case resists shorting.
• Armatures have precision machined and upgraded steel shaft for improved durability and performance.
• Each unit includes a printed copy of the test results so you know exactly what to expect from our parts right from the first time they power on.