Mercury Zephyr Performance and Racing Products

Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:

• Chrome Plated
• 42000 Volts
• Effective To 6500 RPM
• Improved Throttle Response
• Higher RPM Power
• Can Finished In Yellow

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength. Due to torque converter co

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

K&N’s replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,200 different replacement air filters for the majority of vehicles on the road. These filters are washable and reusable and are custom designed to fit into your existing factory air box. Their drop-in design means adding performance is simple. With most vehicles you simply remove the disposable air filter and replace it with a K&N. See applicable instruction sheet for details. Our stock replacement air filters for street vehicles are covered by our famous K&N Million-Mile Limited Warranty and will be the last air filter your vehicle will ever need.

Product Features:

• This is the last air filter your vehicle will ever need!
• Designed to boost horsepower and rate of acceleration
• Can be cleaned and used again
• High air flow with exceptional filtration
• Lasts up to 50,000 miles before cleaning is required depending on driving conditions
• Works with original equipment manufacturer vehicle electronics
• Emissions legal in all 50 US states
• Will NOT void vehicle warranty
• Million Mile Limited Warranty®

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:

• Universal Floor Mount Application
• Base Trimmed For Custom Fit
• Cable Operated
• Quick Installation
• Accurate Shifting

RngPnn

Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.

Product Features:

• Manufactured from high-density cork /rubber blend gasket material
• A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
• Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
• For OE replacement, high performance street, drag race and oval track
• .187″ thick
• Handles Ex Flange Pressure
• Forms Leak Proof Seal
• Black Latex Coating

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal
• Available in Multiple Finishes

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

• Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
• Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
• Raises combustion sealing force to roughly three times that of standard head gaskets.
• Steel wire rings for the greatest combustion seal strength.
• Not intended for use in emission controlled vehicles.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 180 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

The Edelbrock part #41603 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications and have a Black finish. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. Made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

• Small Block Ford 221-351W 62-95
• Tall
• Black Aluminum
• Set Of Two

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 5.70 in. Block To Hub Height
• Black Finish

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Silicone beading on both sides of each gasket
• Complete with manifold end seals and distributor gasket
• For OE replacement, high performance street, drag race and oval track use
• Creates Tight Leak proof Seal

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

• Seat pressure: 115 lbs. @ 1.700″, Open Pressure: 284 lbs. @ 1.200″
• O.D.: 1.437″, I.D.: 1.039″
• Single valve springs with damper
• Approximately .510″ max lift at recommended installed height

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications
• Bolt-on Performance
• Conductor core features DuPont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

Rocker Arms,FS/FW 1.6 7/16 Ultra Pro Mag

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs That Leaky Rear Main Sail
• Silicone Rubber to Withstand Extreme Engine Oil Temperatures
• Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
• Injection Molded for Precise Fit

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

• High Output Fuel Flow
• Flows 130+ gph Free Flow
• Shutoff Pressure Pre-Set From 7.5 To 9 PSI
• Fuel Pressure Regulator Is Not Required
• Heavy Duty Construction For Continuous High rpm Operation
• Redesigned High Flow Valves Always Ensure Adequate Fuel Delivery
• Fuel Body Casting Can Be Rotated For Plumbing Situations
• Inlet And Outlet Tapped For 3/8 in. NPT

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

• Street Performance
• Flows 80 gph Free Flow
• Shutoff Pressure Pre-Set 7.5 PSI
• Fuel Pressure Regulator Is Not Required
• Heavy Duty Construction For Continuous High rpm Operation
• Fuel Body Casting Can Be Rotated For Various Plumbing Situations
• Inlet And Outlet Tapped For 1/4 in. NPT
• Inlet/Outlet Tapped For .25 in. NPT

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.

Product Features:

• HYDRAULIC – Xtreme Energy: Excellent response, good mid-range, stock converter, 3.23-4.10 gear.
• 262/270 Advertised Duration, 218/224 Duration @ .050″, .493″/.500″ Lift, 110 Lobe Separation
• Valve spring upgrade required
• 289-302 Firing Order

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

• Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
• Best with aftermarket converters and more rear gear.
• Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.