from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$151.99

MiniSpool

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M802011 race
All steel construction

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$184.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 7.5″
Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

35 spline
8 x 3.96″ bolt pattern
Cut to length design fits 40″-43.5″ applications
Fits Dana Spicer 60, 70 and 80

from

$47.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$42.99

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

Includes axle bearing and seal
Services one side
Torrington Brand
2.250″ O.D.
1.400″ I.D.

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$8.99

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

c-clip for Ford 7.5″
Fits standard open and Trac Loc applications
Not compatible with Auburn Gear positraction

from

$3.79

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$2.99

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$59.99

Product Features:

USA Standard Gear heavy-duty cross pin shaft
Fits Ford 8.8″ with 7/8″ cross pin diameter
Works with Spartan Locker or standard open spider gears

from

$109.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
Includes carrier bearings and races and “super” carrier shim kit

from

$363.99

Yukon spider gear kit for Ford 8.8″, 31 spline, Trac Loc posi. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects. This kit does not include cross pin shaft or clutches.

Product Features:

Spider gear kit
Fit Ford 8.8″ Trac Loc positraction with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$26.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$13.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$59.99

Product Features:

Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
Interlocking design makes installation much easier

from

$6.99

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$451.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

from

$16.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$329.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Ford 7.5″
7.50″ ring gear diameter
28 spline pinion
10 ring gear bolts
4.56 ratio

from

$49.49

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on