Mercury Caliente Performance and Racing Products

Essential Mercury Caliente Performance and Racing Products

Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)

Mallory Kit: Unil Conv: Delco: V8

from

$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • Easy Installation
  • Improved Fuel Economy
  • Reduced Maintenance
  • Accurate Timing
  • Improved Performance
  • Provides A Simple Conversion
  • No Moving Parts To Wear Out
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)

Exhaust Manifold Gasket Set

from

$45.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

MSD Ignition – Distributor; Ford FE; Ready-to-Run (Part No.8595)

Distributor; Ford FE; Ready-to-Run

from

$569.99
MSD is excited to offer two Ready-to-Run distributors for two classic Ford engines! These distributors are the answer to weak breaker points or rebuilt aftermarket models. Inside the billet housing there is a high-output ignition module. When the maintenance-free magnetic pick-up signals the module to fire, up to 7.5 A is sent to the coil where a powerful spark is created. This improved spark output results in quick starts, snappy throttle response and terrific drivability. The distributors are equipped with a vacuum advance canister for cruising economy. Plus, there is a mechanical advance assembly that is mounted on top of the distributor shaft making it easy to adjust the advance to meet your needs. Another great feature of the Ready-to-Run distributors is their simple installation! All you need to do is connect three wires and you’ll be cruising!

Product Features:
  • Simple and clean three wire installation
  • CARB E.O. Approved
  • Does not require an MSD Ignition Control
  • Supplied w/small dia. cap w/HEI style terminals; race and rotor
  • Will accept PN[8441] Cap-A-Dapt
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
  • Mech. advance assem. can be locked out for crank trigger systems
See More

Holley – Mechanical Fuel Pump (Part No.12-289-11)

Mechanical Fuel Pump

from

$165.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 110 gph Free Flow
  • Shutoff Pressure Pre-Set From 6.5 To 8 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 3/8 in. NPT
  • Inlet/Outlet Tapped For 3/8 in. NPT
See More

B & M – Shift Improver Kit (Part No.50260)

Shift Improver Kit

from

$72.99
Shift Improver Kit – 1967 to 1969 Ford, Lincoln, Mercury C4 Application: 1967 to 1969 Ford, Lincoln, Mercury C4 Recalibrate your automatic transmission for optimum performance and extended life! Select the mode that best suits your application Provides crisp shifts on any stock automatic transmission Eliminates shift overlap and excess wear on clutches and bands due to slippage The B&M Shift Improver Kit the easiest way to get the stout performance you’ve always wanted out of your automatic transmission – and you get two modes of performance to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit. All you need are some hand tools! In the space of an afternoon, you can turn your transmission into a B&M-tuned unit! Ask the thousands of satisfied customers that have installed one in their transmissions! STAGE 1. HEAVY DUTY Firm positive shifts without loss of driver comfort for improved performance in all street vehicles. Recommended for regular passenger vehicles. STAGE 2. STREET/STRIP Provides positive shifts for high performance street use or for competitive events. This level is for the enthusiast who wants the hardest, quickest possible shift.

Product Features:
  • Provides Crisp Shifts
  • On Any Stock Automatic Transmission
  • Eliminates Soft/Sluggish Shift
  • Eliminates Shift Overlap
  • Eliminate Clutch and Band Wear
  • Improves Transmission Life
  • Transmission Removal Not Required
See More

Edelbrock – Performer 390 Intake Manifold for Ford FE, Satin Finish (Part No.2105)

Performer 390 Intake Manifold for Ford FE, Satin Finish

from

$597.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7820)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$67.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
  • For Engine with One-Piece Fuel Pump Eccentric
See More

Mr. Gasket – Cam Change Gaskets (Part No.4410)

Cam Change Gaskets

from

$63.09
If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:
  • Contains all the gaskets needed to change out your camshaft
  • Fuel Injector O-Ring Not Included
  • Meets Performance Standards
See More

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Ultra Seal: Harmonic Balancer Bolt/Washer Kit

from

$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:
  • Heat treated black oxide coated Grade 8 alloy steel
  • Thick parallel ground washer provides more accurate, uniform torque
  • Hex Prevents Socket Slippage
  • Accurate And Uniform Torque
  • Black Plated Finish
See More

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7568)

Valve Cover Gasket Set for Ford

from

$40.99
Product Features:
  • Valve Cover Gasket
See More

Energy Suspension – Control Arm Bushing Set (Part No.4.3102G)

Control Arm Bushing Set

from

$16.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Competition Cams – PUSHROD SET, SBF HIGH ENERGY 1 ST (Part No.7831-16)

PUSHROD SET, SBF HIGH ENERGY 1 ST

from

$75.99
High Energy Pushrods from COMP Cams are an affordable, high quality solution when building street rods, RVs and daily drivers. High Energy Pushrods have a durable one-piece construction that meets or exceeds all OE pushrod specifications and fit perfectly with High Energy and Magnum Rocker Arms.

Product Features:
  • 5/16″ diameter, 6.881″ length for Small Block Ford 255 and 302, ’65-up with Flat Tappet Cam
  • Best choice when building street rods, RVs or daily drivers
  • Meet or exceed all OE pushrod specifications
  • Mate perfectly with High Energy and Magnum Rockers
  • Durable one-piece construction
See More

MSD Ignition – Crank Trigger Kit; Small Block Ford (Part No.8640)

Crank Trigger Kit; Small Block Ford

from

$593.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:
  • Absolutely The Most Accurate Way To Trigger The Ignition
  • The non-magnetic pickup cannot be false triggered.
  • Powerful magnets are embedded in a billet aluminum trigger wheel.
  • Incl. brackets/mounting hardware to fit a variety of engines
See More

Hays – Flywheels (Part No.12-535)

Flywheels

from

$499.99
Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:
  • Certified Billet Material
  • Borg and Beck Clutch Pattern
  • Long-Style Clutch Pattern
  • Ring Gear Securely Mounted To Prevent Spinning
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1963)

Rear Main Seal Gasket

from

$42.49
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Energy Suspension – Control Arm Bushing Set (Part No.4.3102R)

Control Arm Bushing Set

from

$17.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Accel – 8Mm Super Stock Spiral Cust Bu (Part No.5046B)

8Mm Super Stock Spiral Cust Bu

from

$88.99
These ACCEL Super Stock wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with zinc-plated steel terminals.

Product Features:
  • Ferro-Spiral supression core eliminates RFI/EMI
  • 500 ohms per foot of resistance
  • 500 Ohms Per Foot Resistance
  • 550 Degree Wire Temperature Rating
  • Meets Or Exceeds OE Boot Temperature Rating
  • Magnetic Suppression
  • 500 Ohms Resistance
See More

Accel – Contact And Condenser Kit (Part No.8203)

Contact And Condenser Kit

from

$79.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:
  • High Performance Points and Condenser
  • With Integral Conductor
See More

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud

from

$427.99
These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:
  • CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
  • Designed for high performance street and race engines
  • Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
  • Additional clearance, up to 1.650″ O.D. valve spring
See More

Edelbrock – Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1404)

Performer 1404 Carburetor: 500 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$435.99
The Edelbrock 1404 Performer Series 500 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Intake Gasket (Part No.203G)

Intake Gasket

from

$36.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Spectre – Water Neck; Ford 390-428 (Part No.4736)

Water Neck; Ford 390-428

from

$47.99
Spectre’s Ford water neck fits Ford 390, 427 and 428 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:
  • Fits Ford 390, 427 and 428 engines
  • Includes bolts and gasket
  • Chrome plated
  • Easy to install
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Helping You Find the Right Performance and Racing Products for Your Mercury Caliente

You love your Caliente. So we’ve made it easier than ever to help you find Mercury Caliente Performance and Racing Products in our online catalog. Our inventory holds 98 aftermarket and OEM Performance and Racing Products for your Mercury Caliente, ranging from $13.29 to $1,138.99.

We offer parts from 15 brands trusted to make quality Performance and Racing Products for your Mercury Caliente. Before you buy, take some time to read through customer reviews. We currently have 1,344 reviews of Mercury Caliente Performance and Racing Products from previous customers. Some of the top rated parts include Blaster 2 Coil: High Performance Ignition Upgrade with 4.3 stars and Ultra Seal: Valve Cover Gasket Set with 4.7 stars.

Find your Caliente Performance and Racing Products here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Mercury Caliente part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.

Top Performance and Racing Products Brands for Your Mercury Caliente

Our inventory holds Performance and Racing Products for your Mercury Caliente from 15 trusted brands. You’ll find OEM and aftermarket parts from brands like Accel, Mr. Gasket, and Edelbrock, all of which can keep that Mercury happy.
We have Mallory parts available for your Mercury Caliente in categories like Performance Ignition Products. Some of the top-rated Mallory parts in these categories are:
Mallory Kit: Unil Conv: Delco: V8
from $134.99
(1)
Mallory Kit: Unil Conv: Delco: V8
Performance Ignition Kits
Unilite Ignition Module
from $85.29
(3)
Unilite Ignition Module
Performance Ignition Parts

Top-Rated Edelbrock Performance and Racing Products

Leading Edelbrock Performance and Racing Products

We carry Edelbrock brand parts for your Mercury Caliente across several catalog categories, including Performance Fuel Systems. Some of our most reviewed Edelbrock parts include:

FAQs for Mercury Caliente Performance and Racing Products

What are the most purchased Performance and Racing Products for the Mercury Caliente?

Out of 98 Performance and Racing Products for the Mercury Caliente, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets

What are the top-rated Mercury Caliente Performance and Racing Products?

Top-rated Performance and Racing Products for your Mercury Caliente based on customer reviews/ratings are:
Blaster 2 Coil: High Performance Ignition Upgrade
from $49.99
(20)
Blaster 2 Coil: High Performance Ignition Upgrade
“Had one before and blew it up, good easy replacement. MSD makes a good product.”
Ultra Seal: Valve Cover Gasket Set
from $36.49
(3)
Ultra Seal: Valve Cover Gasket Set
“Excellent product. Highly recommend. Easy to install. Quick delivery of order.”
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $51.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
“cometic head gasket is great but prob is dose not seal if the block isn’t mirror finished. many people switch over to felpro and it has worked out gre”